Your cart is empty.
Your cart is empty.Product Description
Specifications:
Total Length: 600mm Head Thread Size: M8*1 End Connection Size For Valve: M8*1 Voltage: >20mV Time For Opening Valve: Less Than 10s
Install Steps:
1. Install the thermocouple tip on a board and use two nuts to fix its location
2. Keep the tip about 5mm from the burner hole.
3. Fix the thermocouple nut M8 on the valve end tightly (Check if your valve end thread is 8mm before your buying)
4. Connect two flat terminals well with the current tilt switch terminals.
5. Turn on the gas and push your valve 5-10s till the thermocouple end is heated.
6. Release your hand and it work well. If failed, please check.
- a. If your thermocouple is heated on flame
- b. If the thermocouple end is well connected with valve
- c. If the terminals connect tilt switch well.
William knowles
Reviewed in the United States on February 21, 2025
To long for my application did not heat properly
Karolina
Reviewed in Poland on August 11, 2024
Ok ,
Customer
Reviewed in Canada on July 24, 2024
Fixed the problem with our fire table. Kept Turing off and now works again and that problem has been fixed
_shopper
Reviewed in Canada on November 19, 2024
No issues. Make sure to clean the water or blow out the moisture in the lines prior.
fixit
Reviewed in the United States on October 22, 2024
great replacement part. had the pizza oven for about 4 years.then it started acting up. it would run for about 15-20 minutes ok, and then cut out.restart, last for a few minutes, then cut out. eventually it would not stay lit.The thermo couple appears to be defective in these.it was not made to be consumer replaceable, bottom panel uses triangle bits, to try to prevent opening.the bits are easily found on amazon. https://www.amazon.com/dp/B0B5GSMPV7 for a few bucks.took about 45minutes probably.
Larry M. Ashby
Reviewed in the United States on October 17, 2024
Used for fire pit. Worked great
Janie
Reviewed in the United States on January 31, 2024
The thermocouple was easy to install. Had trouble finding a metric one locally.
AJL
Reviewed in the United States on January 28, 2024
My Ooni Koda pizza oven is now five years old and the thermocouple finally gave out. I contacted them and they do not offer replacement thermocouples. And they could not assist under the warranty because even though I had the original purchase receipt they require the serial number and unfortunately that’s on a cheap metallic sticker on the rear leg and it burned away. The original Ooni Koda 12 is not made to be disassembled - the base it attached to the top with many stainless steel rivets. Perhaps the reason that Ooni will not offer the part. I drilled out all of the rivets and replaced them with stainless steel sheet metal screws. Anyway, job done and I now have a working Ooni oven again. This replacement thermocouple is perfect.
Moistro
Reviewed in Spain on January 13, 2024
La instalación fue muy sencilla, falta verificar la durabilidad.
Carlos G.
Reviewed in the United States on April 21, 2024
Awesome fit
M. Ganzer
Reviewed in the United States on June 4, 2023
I used this to replace the thermocouple on my Ooni Koda 12. Works well so far. I think they had a bad batch of thermocouples for a spell as this was a common problem. To access the thermocouple you need trangular dirver bits like these. https://www.amazon.com/gp/product/B083HQTCQ5/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Liz Carter
Reviewed in the United States on March 20, 2023
Nice replacement for the Ooni. Much better than $89 for the OEM part. Had to wiggle a tiny bit to get it in, and it was longer so I added a loop to the routing, but super easy and worked right away.
gorgyporgy
Reviewed in the United Kingdom on November 29, 2022
I like it because of its easy fit!
Recommended Products