Your cart is empty.
Your cart is empty.Product Description
Ink Smearing Isuue
A1. The ink is soluble in water. That's why you need to spray a clear sealer on the decal. If the ink smear that means the coating is not sprayed evenly or not thick enough to protect the ink from water, or the ink does not dry completely before spraying.
Difference between the CLEAR and WHITE Decal Paper
The clear and white indicates the water slide decal film color. If you gonna use the water transfer paper on light color or clear surface, the clear is a good choice. Or if you gonna use it on a dark color surface, we recommend you use the white.
How to slide off the decal from the backing sheet?
A3. We suggest you to soak the decal paper in the water for a little longer time, then gently slide the decal from the backing sheet a liitle in the water. And put some water on the object surface before applying the decal on it.
Is it dishwasher safe?
A4. It is not recommended. We recommend washing by hand.
Mcclden
Reviewed in the United States on March 10, 2025
Works great for project
Randall R. Ott
Reviewed in the United States on February 15, 2025
Use these on mugs and guitar headstocks. Works well on inkjet printer then two light coats of lacquer to seal the colors before dipping. Works great
Eric
Reviewed in Canada on June 5, 2024
I actually had to apply 3 to 5 coats of clear and let it dry each time so that the sheet becomes thicker to use and less prone to removing the ink on the back side / take away notes is its difficult doing entire curved objects but not impossible (when water is applied to the backing its a very useful pressing and aligning tool actually and this is a tip I give to you all
Steve
Reviewed in the United States on December 8, 2024
After trying a couple of other water decal products which were too hard to work with I finally tried this brand and Success. Much easier to handle than others, much more forgiving when positioning on the object surface when it comes to potential tearing or crumpling up as compared to the others I've tried. Takes about 4-5 minutes to release from the backing in a plate with cold water. I believe the instructions state 3 minutes. Not quite enough in my experience with this stuff. 3-4 minutes still not bad. Maybe a bit quicker in warm water.
Customer
Reviewed in the United States on December 24, 2024
I have used decal paper many, many times over the years. First time using this brand and only because I needed it urgently and one of the few for 81/2 x 11 paper ones readily available. I found it to be mediocre at best. Wasted four sets because of being too thin and tendency to distort, stretch and tear. Made it work by extra application of topcoat. Cannot recommend, but if used, make several copies of what is needed (expect problems) and apply multiple coats of non-yellowing sealant and let thoroughly dry.
Kindle Customer
Reviewed in the United States on December 12, 2024
If you follow the instructions they go onto plastic like a dream. That being said expect to play with color settings a lot if you're doing anything other then blacks. Browns tend to bleach out and turn orange.
TrayNesia
Reviewed in the United States on December 12, 2024
The media could not be loaded.
Elyse
Reviewed in the United States on November 21, 2024
Love this product! Very easy to use
borntobewright
Reviewed in Canada on February 27, 2023
This waterslide paper did not disappoint. My images printed beautifully. After spaying the paper with acrylic sealer and letting it thoroughly dry, I applied the images to my mug without any difficulty. I will buy again.
Customer
Reviewed in Canada on December 30, 2023
First time using this kind of decals, and it worked perfect. Had only one hiccup with it, but it was my mistake. One thing that one must be aware is, that once you spray the clear coat ensure you use the decal within an hour or two 😉, do not let it dry overnight. I made that mistake and it got ruined 😕. The clear coat had cured and when submerging the decal in the water, the image cracked (lines appeared). As for how long it will last. Can't tell as they were for Christmas presents. Will update if anything changes
Aimee
Reviewed in Canada on January 2, 2022
Comes off paper fast when soaking
Bonnie Laporte
Reviewed in Canada on August 24, 2021
Wow! I make resin products- keychains, ornaments, etc. My friend showed me how to use waterslide paper, and it was perfect for putting a picture on my creations. I purchased this brand, and couldn't be happier. It prints up nicely with my home inkjet printer. I just sprayed it with acrylic spray to seal it (a couple times), let it dry, then cut out the picture, soaked in water for about 30 secs, and slide it off the paper backing and onto my ornament, keychain, or whatever (she does cups). AMAZING!!
John Crisafi
Reviewed in the United States on July 24, 2021
This was my first time using this kind of decal and I found them to be pretty easy to use and effective. I followed the instructions and all of my projects turned out perfectly. Print quality was good and I had no issues with the ink drying.I bought this because my kids love Bluey (the animated show from Australia) so I wanted to make them some wooden Bluey coasters. I bought some 1/2 inch thick poplar stock from HD, cut it into 3.5 inch squares and sanded them smooth. I added a coat of acrylic clear and let that dry, then lightly sanded it so that the water would not raise the grain of the wood. I followed the instructions for these decals and printed them out on my Canon inkjet printer. I let them dry for about 10 minutes and then took the sheets outside and sprayed them with acrylic clear coat twice, with a few minutes between coats, as the can said. I did it again the next day for a total of 4 coats. I cut them out and the submerged one in filtered cool water. While it was submerged, I wiped a coaster with a bit of water. After 20-30 seconds, I took the decal out and placed it on the coaster and gently slid the decal off the paper a bit, then I grabbed the paper backing and slid it out while I held the decal in place. I adjusted it a bit and then smoothed it out and dabbed it lightly with a clean towel. I checked for bubbles and smoothed more with wet fingers, then I dried them again with a towel and let the whole thing dry overnight. The next day, I sprayed 2 coats of acrylic clear coat and the same again a day later. Then I added thin felt pads to the back to let them slide on the table.So far, they have held up well. The decals still look good and they aren't coming off. I did mess up one because I put on too thick a coat of acrylic by accident and it made the decal peel. One coaster was left with water on it overnight and there was no problem the next day when I wiped it off. Good coats of sealer are essential to seal the ink and the coaster, then the whole process seems to go well consistently. I had one or two decals in my second batch that ripped that were entirely my fault. You have to be gentle and I pulled too hard when repositioning the decal.For sure I will buy these again. They are great for small projects for personal use.
Recommended Products