Your cart is empty.
Your cart is empty.Cnc extender adapter made especially for 1/2" Shank router bits., #47641, (D) diameter 1, (D) shank 1/2, overall length (L) 3-5/8, max RPM 18, 000, L1 1-25/32, L2 1-9/16, L3 13/32, D1 1/2, 47641 1/2 inch Shank CNC extension adapter for 1/2 inch Shank router bits
Amber medley
Reviewed in the United States on March 4, 2025
So far so good could be a little bit longer but no complaints
Amber medley
Reviewed in the United States on March 4, 2025
So far so good could be a little bit longer but no complaints
dave
Reviewed in the United States on December 4, 2024
Used with spoil board bit. No vibration. I had to return a cheaper off brand extension, it vibrated a lot. Do not buy a cheaper extension. Amana makes good stuff. I never hesitate to buy Amana. I used it to flatten a log that had been chain sawed for carving, big cuts.
dave
Reviewed in the United States on December 4, 2024
Used with spoil board bit. No vibration. I had to return a cheaper off brand extension, it vibrated a lot. Do not buy a cheaper extension. Amana makes good stuff. I never hesitate to buy Amana. I used it to flatten a log that had been chain sawed for carving, big cuts.
Digger
Reviewed in the United States on December 27, 2024
The extension was just as described and worked good.
Digger
Reviewed in the United States on December 27, 2024
The extension was just as described and worked good.
Neug
Reviewed in the United States on August 31, 2023
Works great for my wood slab flattening table to extend my 3 inch surfacing bit closer to the slab.No perceptible vibrations after two years use until I bent my last one by moving quickly through a large knot hole and entering the wood on the other side too fast in a burr oak slab with a 3.5 HP Festool router.I like this chuck extension enough that I purchased the same one again after mine was damaged.
Neug
Reviewed in the United States on August 31, 2023
Works great for my wood slab flattening table to extend my 3 inch surfacing bit closer to the slab.No perceptible vibrations after two years use until I bent my last one by moving quickly through a large knot hole and entering the wood on the other side too fast in a burr oak slab with a 3.5 HP Festool router.I like this chuck extension enough that I purchased the same one again after mine was damaged.
T2
Reviewed in the United States on March 2, 2023
Excellent quality tool.
T2
Reviewed in the United States on March 2, 2023
Excellent quality tool.
D Man
Reviewed in the United States on July 8, 2021
Worked great to extend the bit
D Man
Reviewed in the United States on July 8, 2021
Worked great to extend the bit
McCord
Reviewed in the United States on December 27, 2021
It was always so frustrating to have to raise your project up off of the perfectly square and flat table to reach the festool router. Now I can cut into the table... this product is well made and well balanced. Will buy again if needed.
McCord
Reviewed in the United States on December 27, 2021
It was always so frustrating to have to raise your project up off of the perfectly square and flat table to reach the festool router. Now I can cut into the table... this product is well made and well balanced. Will buy again if needed.
PAPASWAT
Reviewed in Canada on July 28, 2017
Beefier than I needed for routing out wooden bowls with a template ant 2-3 hp router, but it should do the trick
PAPASWAT
Reviewed in Canada on July 28, 2017
Beefier than I needed for routing out wooden bowls with a template ant 2-3 hp router, but it should do the trick
Monte F.
Reviewed in the United States on February 9, 2017
Worked Great, but the shaft broke off while cutting foam tooling board.
Monte F.
Reviewed in the United States on February 9, 2017
Worked Great, but the shaft broke off while cutting foam tooling board.
Recommended Products
