Your cart is empty.
Your cart is empty.Allstar 4500 Type Series Open Center Carburetor Base Gasket (Pack of 10) is for 4500 type series carburetors and is an open center design. It is backed by a 90-day limited factory warranty. It is sold as one set of 10 pieces.
Robert Bonin
Reviewed in the United States on April 6, 2024
I was needing a new base gasket for my Holley 4500 carburetor; this was an exact fit and shipped faster than expected and was the right price.
Robert Bonin
Reviewed in the United States on April 6, 2024
I was needing a new base gasket for my Holley 4500 carburetor; this was an exact fit and shipped faster than expected and was the right price.
Rosemarie
Reviewed in the United States on June 11, 2023
👍🏻
Rosemarie
Reviewed in the United States on June 11, 2023
👍🏻
pere
Reviewed in the United States on March 9, 2023
the product wasn't very good, is that adhering to the rules
pere
Reviewed in the United States on March 9, 2023
the product wasn't very good, is that adhering to the rules
Linda Larocque
Reviewed in Canada on March 31, 2023
Holes don't match..they're offset..not centered to the carburator
Linda Larocque
Reviewed in Canada on March 31, 2023
Holes don't match..they're offset..not centered to the carburator
Hobo
Reviewed in Canada on December 15, 2022
I don't write any bad reviews but this just frosted me. Paid $15 which is ridiculous for a gasket. Found out the holes needed to be enlarged because they were not centered. Took 1/8" off to the one side of every hole. It doesn't look anything like the picture. The skinny dividing portions were fat and needed to be cut away. Bought this for a Holley Sniper.... doesn't fit without hours of work.
Hobo
Reviewed in Canada on December 15, 2022
I don't write any bad reviews but this just frosted me. Paid $15 which is ridiculous for a gasket. Found out the holes needed to be enlarged because they were not centered. Took 1/8" off to the one side of every hole. It doesn't look anything like the picture. The skinny dividing portions were fat and needed to be cut away. Bought this for a Holley Sniper.... doesn't fit without hours of work.
Steve
Reviewed in the United States on September 20, 2021
Need a 1/4" spacer to get rid of the Holley Sniper EFI whistle? This one will do it, and at a 1/4" thick it didn't cause hood clearance issues.
Steve
Reviewed in the United States on September 20, 2021
Need a 1/4" spacer to get rid of the Holley Sniper EFI whistle? This one will do it, and at a 1/4" thick it didn't cause hood clearance issues.
Chris L
Reviewed in the United States on August 24, 2020
This is a good quality gasket. Used a pair under and over a wedge for a marine 4150 carburetor on a boat.
Chris L
Reviewed in the United States on August 24, 2020
This is a good quality gasket. Used a pair under and over a wedge for a marine 4150 carburetor on a boat.
DPG70
Reviewed in the United States on September 27, 2018
These gaskets measured .062, which is the same thickness as the Mr. Gasket units I am using now. The Mr. Gasket pieces are $4.49 for the 54G and $6.46 for the 54c EACH! I reviewed the .045 gaskets as usable if the mating surfaces are perfect. These .062 will work if the two surfaces are not perfect.
DPG70
Reviewed in the United States on September 27, 2018
These gaskets measured .062, which is the same thickness as the Mr. Gasket units I am using now. The Mr. Gasket pieces are $4.49 for the 54G and $6.46 for the 54c EACH! I reviewed the .045 gaskets as usable if the mating surfaces are perfect. These .062 will work if the two surfaces are not perfect.
Corvettelen
Reviewed in the United States on October 14, 2018
Top quality, excellent machining perfect!
Corvettelen
Reviewed in the United States on October 14, 2018
Top quality, excellent machining perfect!
Jeff Jackson
Reviewed in the United States on March 23, 2015
Gasket was a little to thin for my application
Jeff Jackson
Reviewed in the United States on March 23, 2015
Gasket was a little to thin for my application
Recommended Products
