Your cart is empty.
Your cart is empty.Product Description
Hidden Brackets
Robert Coffin
Reviewed in the United States on March 6, 2025
The media could not be loaded.
Customer
Reviewed in the United States on February 24, 2025
Good buy
anastasia miron
Reviewed in Canada on January 6, 2025
Metal bends very easily. Also would not recommend using screws provided as they broke within the wall when drilled into studs. Overall would suggest purchasing another product.
Abraham
Reviewed in the United States on January 2, 2025
I only needed a few and this had enough to cover my project's need. I used 2 per floating shelf and had to make sure I measure each pair for diameter and angle because there were slight variations in both. They are pretty sturdy if you can get them on a stud. I used deck screws and they are solid! All an all, they got the job done and the wife is happy with the end result.
alex
Reviewed in Mexico on August 15, 2024
Se siente fuertes y de buen materia
Kevin
Reviewed in the United States on July 14, 2024
While using shelves that are 1-1/2" thick, the brackets are too large and I had to drill a new hole in the bracket close to one of the holes provided to be able to secure the bracket to a single stud. For use with attaching to a single stud, the holes that are drilled into the bracket are spaced OK as long as the shelf is a minimum of 2-1/4" thick.
FCB
Reviewed in the United States on December 7, 2024
I used these to hang some floating shelves that I made from some 12 x 4 wood. They worked well and are well made. The hole placement could be better but I made my own holes and was able to use them how I envisioned. I do recommend them.
Karen
Reviewed in the United States on December 6, 2024
They work excellent, but you have to be very careful when you drill the hole in your wood shelf. It has to be exactly straight or else you're going to waller it out. They take a little patience and work, but the end result is gorgeous. The bit for these is going to run you around $25 - $35.
Lynden Johnson
Reviewed in the United States on December 10, 2024
These shelf brackets work as described. No issues with quality. Enabled shelves to be installed with no visible means of support. Shelves were constructed with 1/2 inch gap and they slid right onto the wall brackets with no problems.
G-lenn
Reviewed in the United States on November 15, 2024
I installed these every couple feet along a drink ledge on a 12 foot long piece of walnut. It turned out really nice and I am happy to not see any brackets under the shelf supporting it. I’ve done a few installations like this now and this one went smoother than any other, despite being the most challenging installation to read on if you want some advice…A quick note of the one bit of weirdness going on here… The holes to mount the bracket to the wall are not aligned with the rod that goes in the shelf so just keep that in mind when you’re choosing your mounting locations. It’s not any issue if you plan for it, but if you drilled your holes in your shelf before you recognize that, you might end up frustratedA half inch diameter bit with a simple drill block to ensure perpendicularity worked fine for making the holes in the shelf. I used painters, tape going up on the front of the bracket and down on the back of the bracket. The back being the part towards the wall. A few inches of painters, tape sticking up is enough to ultimately support the bracket after you position, the shelf, but we’ll get to that in a minute. The second piece of painters, tape stuck on the back of the bracket going down is so that you can insert the bracket into the shelf, rotate it to be in the right position, and then tape the lower piece of tape onto the bottom of the shelf to hold it from rotating. After you’ve done that, with all the brackets, get someone to help you position the shelf against the wall, ensuring that it’s level and use the upper tape to stick to the wall to locate the right position, then remove the tape from the bottom of the shelf. After you do that, with all of the brackets, you can gently slide the shelf away from the wall and the brackets will be stuck to the wall in the right locations. Then it’s just a matter of mounting the brackets to the wall and sliding the shelf back over. In my case, my shelf was 12 feet long, making it pretty cumbersome to handle. So I took a board on either end that was cut to length so that the shelf would be at the right height and use that to temporarily support it which helped a lot.I’m not saying it isn’t still tricky but the other times I’ve done this with shorter and lighter shelves, the alignment hasn’t been as good and it made it very hard to push onto the wall so I think this is a pretty good approach. Maybe if I do this again, I’ll make a little video because that’s always clearer than a write up.
MrOtti
Reviewed in Mexico on November 13, 2024
excelente producto a muy buen precio
Great postage as was in description
Reviewed in Australia on September 24, 2023
Good value and they look like they will work well
marko62
Reviewed in Australia on September 22, 2022
I bought these brackets to mount a couple of shelves 1200mm x 240mm x 46mm that i made out of pine to replace the white store bought hollow ones which were going yellow. As others have stated the screw holes are spaced too far apart to get 2 screws in the stud. To get around this problem i had to rotate the bracket 90 degrees so the plate was vertical which meant the plate was wider than the shelf. So i had to cut 2mm off the ends of the plate which made them the same size as the shelf so they can still be seen with a closer look but it is acceptable to me.I used a 12.5mm drill bit for the holes for which both have to be straight which can be a challenge and you will need a longer than standard drill bit.I got around the problem by drilling the holes before i put the shelf together.As others have stated not all the brackets a straight, i found at least one that was a couple of degrees off but luckily i didn't need all eight.I also didn't think the screws were long enough so i replaced them with 75mm screws that i already had, probably over kill but better than what was supplied.
Recommended Products