Your cart is empty.
Your cart is empty.4.6 out of 5 stars
- #4,663 in Musical Instruments (See Top 100 in Musical Instruments)
- #13 in Acoustic & Classical Guitar Nuts
Mark J.
Reviewed in the United States on March 26, 2024
I buy these when the guitar shop needs blanks, the guys like how they sand and look without a bunch of buffing. I will buy again, and again....
Heriberto Cervantes
Reviewed in the United States on February 29, 2024
fits for any 12 string takamine
Angel
Reviewed in the United States on February 20, 2024
Never did any guitar repairs or setup but this was a great experience and worked out well for me.
01 AQ4
Reviewed in Japan on January 26, 2024
硬くてなかなか削るのは難しいけど、お買い得
sec
Reviewed in Japan on February 13, 2023
サドル削りで底の平面を出すのに失敗が多い初心者です。安くてたくさんあるのがいいと思いこの商品を選びました。6本入っていてこの値段は安いと思います。割れや欠けはありませんでした。オクターブピッチの傾きは自分で加工しなければなりませんが価格からすれば仕方ありません。余談ですが、飼い猫が匂いを嗅いで1本咥えて持って行こうとしたので、材質も確かに牛骨なんだろうと思います。
品川直紀
Reviewed in Japan on December 9, 2023
ちゃんとした骨なんでしょうね。簡単には削れません。
Larry Dunn
Reviewed in the United States on October 24, 2023
Exactly what I needed. Great price and fast shipping. I’ll be ordering more.
studio-mamiya
Reviewed in Japan on January 8, 2023
普通に使えるもので、骨密度も問題なく音も悪くないです。切断後にわずかに反ったと思われるのが１枚ありましたが、これは実験に使うと思います。マイクロメーターで厚みを計りましたが、3.00mmを切るものはないです。微細な刃物跡があるので表面をヤスリで平滑にしましたが、表裏を各0.05mm ほど削ると取れる程度の浅い刃物跡ですので、中国製の中では優秀だと思いました（次に買ったらどうかはわからないのが中国製ですが）。1) 厚みを各３点で測定： 3.01mmから3.10mmで、多いのは 3.06mmあたり2) １本あたりの最大の厚みの差：max 0.04mm , min 0.02mm※クラシックギターだと、これを 2.40mmあたりまでブリッジに合わせながら削っていきますアコースティックギターだとこのままの厚みで使います。今回のは良い素材だと思いました。
dirtdawg
Reviewed in the United States on April 13, 2023
These are consistent and certainly worth the price. You could pay more, but why?
Paul S. Lewis
Reviewed in the United States on August 20, 2022
Six pieces arrived in a nice, reusable package. Just a tad thick allowing for fitting as needed. Dimensions seemed consistent. Very nice overall and easy to quickly get to desired fit and finish. First one I used came out excellent.
Matty Naylor
Reviewed in the United States on May 22, 2020
The package arrived safe and right on time. The saddles were intact and none were broken or damaged. I measured each saddle with digital calipers and they measured between 2.95mm and 3.05mm thick, 80mm long exactly, and between 9.95mm and 10.05 mm tall. So the sizes are acceptably accurate to the description. 4 of the saddles were perfect. They were smooth, hard, and consistent, and perfect material for a guitar saddle. The image with the green check mark is one of the perfect ones I received. One saddle was full of pits and air pockets, rendering it useless for a guitar saddle, air pockets and inconsistent bone is a no-no. This is the saddle with the big red circle, to show where all of the issues are located. Another saddle had a couple of air pockets but I can still use the saddle because I can compensate the saddle to remove the bad area. So I recieved 4 perfect saddle blanks, one flawed but still salvageable one, and one that is completely unusable.
Kayle Goulding
Reviewed in Canada on December 2, 2020
Good quality, bit on the expensive side for blanks but not bad.
Customer
Reviewed in the United States on December 24, 2019
I replaced the plastic saddle on a new cheap guitar with one of these. It took about 20 minutes to trim it to length and adjust the height (a Dremel tool makes it easy) and the results were really good. It eliminated the jerky tuning and improved the tone.
Recommended Products
$16.55
$ 6 .99 $6.99