Shopping Cart

Your cart is empty.

Your cart is empty.

5Pcs Ir High Power LED Chip 3535 SMD 3W Infrared Emitting with Aluminum Plate 20mm Star PCB Base Heat Sink for Infrared Transmitter (120deg,IR 1050-1055nm,DC 1.4-1.6V,700mA,42mil chip)

Free shipping on orders over $29.99

$19.29

$ 7 .99 $7.99

In Stock

1.Color:Purple365-370nm


About this item

  • This high power LED light utilizes a high quality chip, 999 gold wire soldering and a ceramic base. In addition, it is equipped with a 20mm star PCB base to dissipate heat and ensure superior quality in use
  • LED light bead adopts high quality aluminum base plate base, small size, light weight, can be configured and welded as needed. It is easy to dissipate heat and has good protection for the lamp beads, thus prolonging the service life of the lamp beads
  • Infrared light with a wavelength of 1050nm-1060nm is characterized by obvious thermal effect, high safety and easy control. Therefore, it is usually widely used in infrared thermal imager, infrared spectrometer, infrared camera and other instruments
  • This high power light is widely used in surveillance camera light, medical light, special light source, VR, AR, virtual reality and so on
  • The recommended operating temperature range for this product is 40-60°C (104-140°F). Our LED chips come with a heat sink substrate and we recommend that you monitor the temperature. We recommend using a constant current LED driver for best performance



Product Description

LEDGUHON

SMD LED Chip With Base Heat Sink

1
3
4

Color wavelength can be freely selected according to the need

SMD LED Chip With Base Heat Sink

JH-3535IR12G42-T8B-1050 Important parameter

Continuous Forward Current 700mA
Peak Forward Current 1000mA
Reverse Voltage 5V
Power Dissipation 3000mW
Electrostatic Discharge 1000V
Operating Temperature Range -25°C to +60°C
Storage Temperature Range -35°C to +80°C
Lead Soldering Temperature 260°C
Forward Voltage Infrared 1.4-1.6V
power dissipation Infrared 50-100mW
power dissipation Infrared 1050-1055nm
Reverse Current 10μA
Viewing Angle 120deg
Recommend Forward Current 700mA
Test Condition IF=700mA
5

Jeffery Cruz
Reviewed in the United States on January 23, 2025
Item was as expected and on time
Terran
Reviewed in the United States on January 14, 2025
I tested the 490nm module and I can confirm that the wavelength is accurate as described (see figure).Note that you will probably need a heat sink to mount these on.
Karl in TN
Reviewed in the United States on July 27, 2024
Flashlight was a nice presentlast Christmas, very lightweight, very bright and very useful. Used every night for pet dogs roundup! LED flamed out one night 4 chips down to one chip lit and weak. Very difficult to identify. Unable to identify so had to adaplt. This is 20 mm diameter, typical 3.0-3.7 volts 3 watts. Modified mounting slightly with very satisfactory results.
Rich H.
Reviewed in the United States on May 27, 2024
Good: Performs as advertised. Bright, true-white light; the steel case I glued it to serves as an adequate heat sink.Bad: Nothing significant.Bottom line: I bought this to replace an incandescent bulb in an old 8mm film viewer/editor that had weakened so much that the picture was barely visible. I was a bit reluctant to use a lamp that runs directly from line current, wondering whether it would need a huge heat sink to keep from overheating. But it does work; the steel case I epoxied it to is enough to keep it cooled, and the wiring job was drastically simplified. I don't think it's perfectly in line with the projector lens, but it's certainly brighter than the old lamp. It's doing the job I expected of it, and doing it well. Five stars.
mike barnes
Reviewed in the United States on March 29, 2024
led's work great
Jeremy McIrvin
Reviewed in the United States on November 22, 2024
Product was as described and came quickly