Enjoy free shipping on orders over $29.99

US Dollar

0 $0.00

Your cart is empty.

512HZ Pipe Locator Receiver, Underground Pipeline Tester Locator Sewer Inspection Receiver Portable Drain Sewer Locator Detector Plumbing Snake Pipe Locators, with LED Screen, for Exploration

4.6 (3) Write Review

Free shipping on orders over $29.99

$539.99

$ 99 .00 $99.00

In Stock

Qty.:

Product Description

with LED Screen for Exploration

SEWER INSPECTION RECEIVER

Audio Output: 50-1000Hz depends on signal strength

Operating Temperature: -20°C to 60°C

Product Size: 548x65x50mm / 21.6x2.6x2.0in

Sensor: Separate angle sensor for peak and 0 signals

Pipe Inspection Receiver Sonde Transmitter for Sewer Camera

Sewer Inspection Receiver 512Hz Pipe Receiver

Pipeline Detection Locator-Easy to use

Working Frequency: 512Hz

Material: ABS

Gross Weight: 2049g / 72.3oz

Modulation: None

Batteries: 6 AA alkaline batteries (shipped without batteries)

Use Time: 4 hours intermittent use

Portable Mini Sewer Camera Locator

Package List：

1 x Host

1 x Receiver

1 x Manual

1 x Aluminum Case

Pipeline Detection Locator Sewer Camera Locator

General Layout：

Power on and off (long press to power on; long press to power off)
A near or far switch controls overall sensitivity. The far position is recommended when starting to position the probe. When you are close to the transmitter and the meter goes to full scale and you cannot desensitize any further, switch to Near to pinpoint its precise location.
Meter Indicators: Indicates the strength of the peak signal (right) and 0 signal (left).
Speaker: Allows you to hear the transmitter's signal beeps or continuous sound, depending on the transmitter use case.
Battery Indicator: Displays battery health status.
Instructions for use: Adjust the locator near or far switch and signal + or ‑ according to the actual environment to make the locator better match the transmitter.
It is recommended to set to Far mode (Signal is set to 9) at the beginning. When the LED screen shows that the signal is very strong, reduce the signal sensitivity level (you can hear a louder sound at the same time), and then you can narrow the detection range.

Note：

The 512 has only one mode, the sonde mode. Receiver in sounding mode. Search for signals emitted by a small detector or camera with a built‑in transmitter that has been routed through a duct. The detector must emit a 512Hz signal, and the receiver can determine the approximate depth of the target.
Start by turning the receiver on, walking around, keeping the receiver at waist height, and walking in the general direction of the transmitter while slowly sweeping the receiver back while pointing in the direction of the transmitter. You will notice that the signal will get bigger. As you get closer, reduce the sensitivity as needed to keep it within range. Toggle the switch to Nearby when you can't keep the meter below full scale
Continue in the direction of stronger signal. When you get to the point where the signal seems to be the strongest, whichever direction you move will make it weaker, then you know you've found a detector that's just below the center of the mast. Move to another place, look for this peak signal again, and see if you always come back to the same place for confirmation. If you followed each step correctly, you should find yourself above the launcher every time. Keep practicing until you get consistent results.

512HZ Pipe Locator Receiver Model WP9701 / WP9701A / WP9701B Package List:

1 x Host

1 x Receiver

1 x Transmitter

1 x Manual

2 x Manual

1 x Aluminum Case

(NO other accessories)

5 Other Accessories:

1 x Transmitter Connector; 1 x Antenna; 1 x Earphone

5 Other Accessories:

1 x Transmitter Connector; 1 x Antenna; 1 x Headset

Dragon China

Reviewed in the United States on April 15, 2025

Good

Customer

Reviewed in the United States on July 22, 2023

It already paid for itself and I don't work in this industry