Your cart is empty.
Your cart is empty.Product Description
ICSTATION
- ICStation has 9 years exprience about electronic industry products
- After-sales service, all customers' email will be follow up in 12 hours even in holidays
- Take charge of all defective items by provide replacement
- Looking forward to your inquiry and hope to built long term cooperation relationship with you!
Silicone Rubber Heating Pad
12V 25W 80X100mm 200℃ Max
Silicone heating pad uses silicone rubber as insulator outside, and the Ni-Cr alloy wire as electric heating element inside, which make it able to be in close contact with the object being heated.The heater blanket is thin, lightweight and flexible. With excellent dielectric strength, fast heating and perfect heat transfer efficiency, the rubber heater pad can quickly provide heat to where it is needed.
Withstand up to 200℃
The silicone heater mat is convenient and safe to use for its service life is up to four years with thickness of 1.5~2mm and max withstand temperature of 200℃.
Parameters
- Working Voltage: DC 12V
- Power: 25W
- Mat Size: 80 X 100mm/ 3.15 X 3.94inch(L*W)
- Power Tolerance: ±5%
- Insulation Resistance: 50 MΩ
- Voltage Withstand Strength: 1500v/5s
Wide Application
The silicone rubber heater can be used for mixing and heat preservation (oil drum heater) in industrial equipment, pipes, tanks, and can be used in blood analyzer, corset, test tube heating, etc..
It can be directly wrapped around the surface of the object to be heated when in use.
J. B. Kramer
Reviewed in the United States on February 3, 2025
We have had them for awhile now. One developed one small hole. Otherwise all have functioned as claimed.
Denis Bergeron
Reviewed in Canada on February 19, 2025
Very good stock. Thank you
randall mccombs
Reviewed in the United States on January 20, 2025
I use these with my solar to keep my shop from getting to cold and they have preformed great
Davie
Reviewed in the United States on September 12, 2024
Bat(s) in insulation w 4 series heaters, surface temp between heater & bat 123F—OK for bat ABS housing durability. Open air heater test temps are lower. Wiring 1, 2, or 3 in series generate higher temps (be careful!) than 4. Is 165F OK for ABS? Use two methods to control heaters in case one fails on!!! Like 2 snap disc thermostat (clean simple) (Amazon, more options direct from mfgr), go with 40F ON since tolerance is +/-5F. or 1 snap disc (w higher than 40F ON) & temp controller. Nice design: Search for DIY Battery Heater for Li-Ion Batteries, has Test data in replies.
Bookoo
Reviewed in the United States on August 4, 2024
I have 6 lithium batteries and purchased two orders of these pads. As suggested. I wired a set of four in series to cut the temperature in half. Purchased two temp controllers to run each set of three batteries. I tried one string of eight and they didn't get warm enough to be useful thus two sets of four.
J. Egan
Reviewed in the United States on November 25, 2024
I'm heating a NOCO NLP20 LiFePO4 battery that sits on the tongue of my trailer. These four pads are wired in series to get a "low and slow" heat for the battery. I tested three pads in series and measured 88.5°F on a single pad. Adding the fourth pad lowers the temperature to right about where I want it.I paired the heating pads with a Bayite DC 12V Fahrenheit Digital Temperature Controller set to keep the battery in the 40°F to 50°F range.I went with this approach to keep the battery warm, but never hot.
Tim
Reviewed in the United States on December 3, 2023
Mostly leaving a review to corroborate what others on here have already said. Took some pictures to get an idea of expected amp draw and temperatures. I am using these with a thermostatic relay to keep a lithium battery warm. I will be using them linked in series. It may seem counterintuitive, but hooking in series reduces the amp draw on the battery as well as reducing the heat output. You can see in the pictures when single these get quite hot 250-260°F, but in series they were averaging 120 to 130°F. They come up to temperature quite fast, just a few seconds and there's a noticeable difference. Also these tests were done in a 30° garage. Only took about 1-2 minutes for them to reach their full temperature. Hooking three in series yielded about 0.7 A draw and a 71.5°F average of the three. One note is all were within a half degree of each other which means internal resistance of these units seems to be very consistent.
BRAD PETERS
Reviewed in the United States on December 9, 2022
a lil too small but will work. have to do some changes to the wiring design.
davek
Reviewed in the United States on December 16, 2022
Lithium Iron Phosphate (LFP) batteries are terrific but can only be charged when they are above freezing. In cold-weather camping, this can be a problem as well as an RV in storage for long periods in cold climates. I have used these pads with two different thermostats and they work very well. I attach two of them in series because I found they got too hot when used individually. I used a Morningstar Relay driver to drive a small cheap relay for one set up. That relay driver can be set up to run multiple sets of pads so I had one pad set turning on at 42F and the other turning on if the battery temp got to 38F. Usually, only one set turned on and it worked perfectly to keep a large (430Ah) LFP battery comfortably above freezing.A less expensive option (Morningstar Relay drivers are over $100) I've also used are snap disk thermostathttps://www.amazon.com/Thermostat-Switch-Circuit-Large-Flange/dp/B0026S6WGK/ref=sr_1_2?crid=1AKM94LJTK81Q&keywords=snap+disc+thermostat+switch+on+at+35&qid=1671214245&sprefix=snap+disc+thermostat+switch+on+at+35%2Caps%2C189&sr=8-2wired in series with the pads and hooked to the battery that is being warmed. They allow power to flow to heating pads when ambient temp reaches 35F and turn pads back off when temp climbs above 45. For $14 for the thermostat plus around $22 for 4 pads and a bit of wire you get an effective battery warmer that actually works.
Recommended Products