Your cart is empty.
Your cart is empty.Product Description
JDHGSHL Heavy Duty Adjustable Pipe Bracket Clamps
Split ring pipe clamps introduction:
Adjustable pipe bracket is a tool suitable for fixing pipes of any material. You can use split ring pipe hanger to secure pipes to walls or ceilings. The surface of heavy duty conduit clamp is galvanized, making it more corrosion-resistant. Galvanized clamp itself is thickened, and its strength is unmatched by products of the same level. There are thickened rubber pads on the pipe clamps, which can reduce wear and tear on the pipes and protect them. We provide matching double-headed threaded nails and plastic expansion tubes, help you install more easily.
Product Details
- The 0.6-2.5 inch (15-64mm) pipe clamp has protruding tapping holes on both sides, which increases the contact area with the screws and makes the installation more secure.
- The surface is wrapped with thick rubber pads, which reduces wear on the pipes during use and better protects the pipes.
- Widely used to support various pipes, such as drain pipes, gas pipes, garden hoses, electrical conduits, etc.
Please measure the outer diameter of your pipe carefully to choose the most appropriate size.
nate
Reviewed in the United States on January 29, 2025
Galvanized garbage
Shawna Harvey
Reviewed in the United States on June 4, 2024
Got these for my husband. Easy to use and work as they should. Great addition to his tool box.
Art w
Reviewed in the United States on June 27, 2024
I used these on round gutter pipes. They held the pipe in place, maybe could’ve had a bit longer lag bolt. But over all I am pleased. Hopefully they fade with the galvanized gutters evenly.
Fred Bloggs
Reviewed in the United States on March 7, 2024
I bet that whatever reason you are thinking of buying these clamps for; it was not for the same reason I needed them for. First off, I see that on the sellers page there are 13 different sizes available from 0.6” all the way up to 8.7”. To be completely fair, I can only speak to the quality and construction of the size I got which is 4.9” to 5.1” (125-130mm) You can assume that the other sizes are similar, or maybe not.My clamps look very well made and sturdy. The weak point is usually where the threaded nut is attached to the semi circle. These people have solved that problem because it is very tight with no wobble or rotation. The thread size is M10x1.5 which is useful to know if you plan on bolting these to an I-beam. If you plan on using the supplied lag screws to put these in brick or concrete, the M10 end has a T25 Torx hole in it. You will never generate enough torque with a T25 bit to force these screws into masonry. Buy two M10x1.5 nuts, double nut the lag screw and turn it in. You’re Welcome! Please hit the “Helpful” below to help me with my ratings. The entire thing is galvanized (Zinc Plated) so it should not corrode even in a damp basement. The rubber protectors are worth a mention. Most clamps come with narrow rubber ‘edge guards’ which can easily dislodge. These protectors are much better than that. They protect 100% of the inside of the clamp and even have 3 raised ribs to stop any sliding movement.So, why did I get them? I have a Jeep with a Dodge Demon motor which requires a lot of clean fresh air. I have two 4” snorkels with two 5” air filters built inline. I got these clamps to hold the air filters in position and stop the filter canisters from vibrating at speeds over 130mph. I removed the protectors and sprayed the metal with ‘Firecracker Red’ to match the Jeep. Then put the protectors back on and the whole thing actually works and also looks great. I know, if there are no photos it didn’t happen!There is a reason for that. I believe I might be the last Human on Earth who does not own a cell phone. No thanks, I don’t want one and would not even accept a free one. I probably should buy a camera though.Bottom line is; They look great and they work great!I recommend these clamps!
Bob K.
Reviewed in the United States on November 26, 2024
On one of the split rings, the screw threads into the ring nut. The second hanger will not assemble properly. The screw will not screw into the nut. Inspection of the nut reveled that the nut has two different size threads on the ID, one smaller and one larger. The larger thread is needed to attach the screw. The nut was installed improperly when manufactured. The larger screw thread will not thread into the smaller nut thread.
Ralph Goers
Reviewed in the United States on October 22, 2024
I used these along with 10 feet of 4 inch black ABS pipe to make a candy chute. With screw adapters I was able to screw these into camera tripods to make the height adjustable.
dion m.
Reviewed in the United States on October 22, 2024
Very nice hangers.
Hippy Bryan
Reviewed in the United States on April 2, 2024
These work great for mounting lights! I see others have found creative uses for these to mount things to pipes rather than mounting pipes to things, so thought I'd add the application I found them useful for. The dual thread mounting makes these very versatile. Technically, there's a M10x1.5 and M8x1.25 threads for the mount. These threads are pretty close as well to 3/8-16 and 5/16-18, and would probably hold that kind of bolt as well. With the lights I tried them on, I had to add a couple of washers to get them to tighten the light mount yoke properly, but it makes for a secure easy way to mount lights to a lumber rack while allowing their easy repositioning. There are lags and expansion sleeves if one chooses to use them. The lags have a hex at the thread transition for tightening from the middle, or one could double nut the machine threads. The pipe clamps gripped 1" copper and EMT pipe just fine, with the rubber lips protecting from chafing and noise and making a secure fit. These clamps with their multiple mounting thread options can find many uses around the house or vehicle, I'm glad I got them!
Recommended Products