Shopping Cart

Your cart is empty.

Your cart is empty.

2CH AHD TVI CVI 1080p HD Video Multiplexer CVBS 2 Channel Video Coaxial Multiplexer for Hikvision Hdcvi 1080P 2MP CCTV Camera 2 Cameras by 1 Cable for CCTV Security System (2CH Multiplexer)

Free shipping on orders over $29.99

$49.99

$ 24 .99 $24.99

In Stock

About this item

  • It supports 2 channel video signals in one coaxial cable by way of Frequency Division Multiplexing.
  • Perfect quality effect,support AHD/CVI /TVI up to 1080P;
  • Transmission only in one coaxial cable without any delay and interference. Saving the cost of the wiring.
  • Widely used in outdoor street, large factories, long distance transmission, etc
  • Package Content : 1 x multiplexer Transmitter;1x multiplexer Receiver;1 x Manual(NOTICE: DC12V 1A power Adapter No included)


2CH AHD TVI CVI 1080p HD Video Multiplexer 2 Channel Video Coaxial Multiplexer For Hikvision Hdcvi 1080P 2MP Cctv Camera

2 Cameras by 1 Cable for CCTV Security System

Key features:

1. it’s designed according to projects with minimum installation volume requirement.

2. 2-CH video in one coaxial cable transmission.

3. FDM technology is easy for multi-channel signals transmission only in one coaxial cable without any delay and interference.

4. Perfect support coaxial video line, 75-3, 75-5, RG59 wire, etc.

AHD (made by XM): perfect quality effect, support 720p, 960p, 1080p

CVI (made by DAHUA): perfect quality effect, support 720p, 960p, 1080p

TVI (made by Hikvision): support 720p, 960p, 1080p, 3mp


Introduction:

This product uses special compression modulation technology, on the front end (transmitter) let 2-channel CVI/AHD/TVI hd

camera to compressed, then made into digital signal in coaxial cable transmission. The back-end (receiver) through

modulation, reductive into 2-channel hd signals for hd DVR (CVI/TVI/AHD) or matrix use after decompression. This series of

products can be in adaptive adjust transmission distance within 0-400 m.

It supports 2 channel video signals in one coaxial cable by way of Frequency Division Multiplexing, with all data

transmission real-time and all images high-definition and non-delay. It is suitable for improvement of

old projects and building under new projects.

Installation:

1.Plug the line cord to an outlet with grounding.

2.Connect input video cable to the input BNCs

3.Connect output video cable to the output BNCs

4.Turn the power switch to the ON position

Environmental:

Operating Temperature: -10℃-+45℃

Humidity:90%

P


Donald
Reviewed in the United States on May 31, 2024
Short of it slightly degraded image possibly, low power draw, works. I don't know if I would use it to save cable but saved me from from having to rerun a very difficult run. Can not speak for longevity as it has not even been a day yet.I have 2 cameras next to each other and one of the cables went bad. The runs are at least 100 yards of rg59. I am able to run both cameras over the one good one now. I'm almost positive the picture on both cameras is slightly distorted/colors might be different but it is still very usable. I am powering both the multiplexer transmitter and receiver with 1 12v 2amp power supply and that is with the camera and the transmitter being at the end of the over 100 yard run. I have attempted to measure the amperage and it is very low for running all 4, it was barely even registering, and the power supply is cool to the touch. Also tested it with all the different modes (ahd,tvi, etc) and they all seemed to work though some may have looked better then others but not sure how they looked before passing through multiplexer. In my opinion well worth the cost and trade offs for saved labor of new cable run.
RSS Santa Fe
Reviewed in the United States on September 25, 2023
Don't waste your money on this multiplexer. I tested it using 3-4' lengths of analog cable and the video color was degraded and there were shadows.