Your cart is empty.
Your cart is empty.Product Description
Product parameters
- Withstanding voltage : 50V.
- Foot pitch : 5.08MM.
- Installation method : in-line (2 pins)
- Tolerance : ±10%.
Package list
- Packed in a small boxes # Easy to save and use
- Brightly colored model label # Easy to distinguish
- 100pcs 220nF 0.22uF 224 Ceramic Capacitors
LOU
Reviewed in the United States on February 2, 2025
Previous to this purchase, I received 4.7nF capacitors which I purchased from two other sellers and they all had high readings on my tester. Most read over 7.00nF. I don't understand it and the sellers had no answers. Capacitors from this seller had very accurate readings.
TMac
Reviewed in the United States on February 17, 2025
Received only 99 instead of 100. Not a deal breaker.All marked 106 (10 uF).Sampled and tested about 6 pieces. All read right at 8uF +/- 1%.Would be nice if they were as advertised.
Beowulf and Migwit
Reviewed in the United States on February 12, 2025
Overall, these are fine capacitors at an average price. Nicely packaged and suitable for my hobbyist applications. At 7 cents each, you could find cheaper bulk priced from a supply house, but shipping would eat that up. Amazon has lots of combo packs that are a better deal, but if you need a lot of this value, then this is as good a way to go as any. The actual capacitance value reads quite accurately.
Joseph Esposito
Reviewed in the United States on January 1, 2025
Nice small tidy pack of 10nf capacitors. Work well in breadboards and perf boards. as a bonus, the small plastic case is actually better than most. It has 2 separate latches that keep it closed and it stays closed well unlike other cheap plastic cases i have.
Steve Barkes
Reviewed in the United States on December 22, 2024
These capacitors seem to be of high quality and were well packaged. Markings were good and easy to read.I checked 10 of them with my component tester, and all values were within 12% of the rated value. These are perfect for use in decoupling to isolate noise in your electronic projects, and it nice to have a large quantity available.
S. Blakley
Reviewed in the United States on December 19, 2024
Primarily used for noise filtering and power supply smoothing near the component, these capacitors are valuable when working on or designing circuits that use micro-controllers. They also have applications in noise filtering in audio equipment and RF circuits.These capacitors are good to have on hand for those who repair today’s electronics, circuit designers and exterminators.
Al W.
Reviewed in the United States on December 10, 2024
These are just what they say they are. New ceramic caps 10nF (about) with through hole legs for a PCB. I grabbed a few and they all seemed to measure a little high (11.6, 11.5, 11.4) but that's well within 20% (8nF to 12nF) and where you usually use these the exact value isn't that big of a deal, anyway. I didn't test all of them, but I didn't find any outside that range of the handful I did test.As shown, these are packed in a box not on a reel or a bag, so if you are hand soldering that's a plus (in my opinion).
Effdub Wheezy
Reviewed in the United States on December 10, 2024
This lot of 100 10nF monolithic ceramic capacitors comes in a small plastic box with a snap closure. The box has a label on the lid that shows the quantity and value (helpful). They are perfect for low-voltage DIY electronics projects, such as assembling radios or things like guitar effects pedals. I tested about 20 capacitors on FINIRSI DSO-TC3, and most were within the 10% tolerance. About 15 were higher than 10nF and the rest were a bit lower. This is quite acceptable for this type and tolerance rating of capacitor. The lead spacing is 5mm, which is perfect for guitar pedals, as that is the most common spacing for non-polarized radial capacitors.
Recommended Products