Shopping Cart

Your cart is empty.

Your cart is empty.

200 PSI Pressure Transducer Sender Sensor with 1/8' -27 NPT 316 Stainless Steel Thread and Harness Connector for Oil Fuel Air Water Pressure

4.8 (3) Write Review
Free shipping on orders over $29.99

$14.99

$ 7 .99 $7.99

In Stock

1.Size:150 Psi


  • 【Specification】Input: 0-200 psi. Output: 0.5V – 4.5V linear voltage output. (0 psi outputs 0.5V, 50 psi outputs 2.5V, 100 psi outputs 4.5V.) Thread: 1/8”-27 NPT. Accuracy: ±1%FS.
  • 【Application】The measuring range of the pressure transducer is 0-200 psi. Widely used in oil tanks, gas tanks, diesel tanks, and more to detect oil, fuel, diesel, gas, water, or air pressure inputs.
  • 【Strict Quality Control】Pressure transmitter made of high-grade 316 stainless steel and high temperature-resistant plastic, it can work greatly in various environments.
  • 【Better Performance】Gas, liquid, and other physical parameters of the pressure sender sensor can be converted to standard electrical signals. Furthermore, the pressure sensor switch is Lightweight and small in size, convenient to install and operate, plug and play.
  • 【Warranty】This product provides a 1-year replacement or 50000km promise. Strictly inspected and tested before shipping, if you have any problems with the AULINK product, please feel free to contact us via Amazon message.


Product Description

AULINK 200 PSI Pressure Transducer Sender Sensor
AULINK 200 PSI Pressure Transducer Sender Sensor
AULINK 200 PSI Pressure Transducer Sender Sensor
AULINK 200 PSI Pressure Transducer Sender Sensor
AULINK 200 PSI Pressure Transducer Sender Sensor
AULINK 200 PSI Pressure Transducer Sender Sensor
AULINK 200 PSI Pressure Transducer Sender Sensor

Máximo Castanho
Reviewed in the United States on February 15, 2025
Excelente instrumento de medición muy buen acabado, materiales de calidad y mediciones bastante confiables.
Gabriel Rosa
Reviewed in the United States on December 9, 2024
Love the electrical connector
J. Anthis
Reviewed in the United States on October 2, 2024
TL/DR: 2 working well, 1 failed, 1 on the shelf. For $13.99 I will buy many of these if I need to.I am building a turbocharged rotary engine street/strip car and I need at the least mostly reliable data. Unfortunately, times are tougher than they need to be and everything is expensive. I had already purchased AEM sensors with 3 pin weather connectors and wired them into my custom engine harness. Unfortunately the AEM branded sensors (100PSIG, and 150PSIG) both failed one at first start and the other while tuning. They were around $75/each. Which is why I am here. AEM uses a 3 pin weather connector with the same pinout as AULINK for +/- and signal. This turned out to be very convenient for my application as I did not have to rewire the connector that came with this unit.So far it has been through roughly 20 hours of driving on 1 sensor, and about 18 hours of driving on another. (both are 100psig) I purchased 4 total. 2 for use, and 2 for the shelf. 1 sensor give me bad readings after a few hard pulls while tuning. It is possible that my oil pressure which is regulated to 100psi at full throttle simply failed due to being out of range. It's possible this sensor was $13 and you get what you pay for, unless it says AEM on it. I swapped it for another and it has been solid since.I am currently using these to monitor both fuel pressure and oil pressure. Because I am manifold referenced, which means my fuel pressure changes with vacuum and boost pressure, I need to tell my fuel computer what the new fuel pressure is to ensure the correct fuel volume is injected. Both read right on the money with my mechanical gauges.If you are building a project car this might be the right choice for you. My car is for fun, and I am not a professional, but am doing everything myself and this was a breath of fresh air in an otherwise too expensive world. I will update this review if/when another sensor fails.