Your cart is empty.
Your cart is empty.The FERAL ATV Gear 3-Way Hitch fits all ATVs and UTVs with a 2" receiver. Our Hitch Plate is laser-cut from extra high strength steel. The unique design incorporates all features from one integral piece of steel... Eliminates welds, creating an inherently superior design. It's plenty strong, just waiting for you to try to abuse it... Powder-coated for superior durability, providing unmatched protection and life. The hitch ships with the hitch pin and clip included. The FERAL ATV Gear 3-Way Hitch enables use of a ball, pin pull, or tow loop without needing to change hitches.
Nor'easternor
Reviewed in the United States on August 30, 2023
does not work in my 3 Curt brand hitches so I reduced by one star, as the hitch pin hole is off by 1/8” or so as it hits the weld on the top plate before going in far enough to align the holes. I returned it no problem and bought the longer 9” version also by Feral & that worked great. Again very heavy duty for my purposes of dragging trailers and implements around the property.
Christopher Kline
Reviewed in the United States on November 3, 2023
Works perfectly for what I need, and made in the USA!
swangersVA
Reviewed in the United States on July 31, 2021
Had bought the bolt on Feral hitch for 2002 Grizzly and used for years. Got this 2" slide in hitch immediately when I got a 2021 Kawasaki Teryx and it's been on ever since. Bolted on a ball and pull trailers around the house without worry.
Mark
Reviewed in the United States on June 6, 2020
This seems pretty sturdy for an ATV hitch. The plate is single piece construction as advertised, versus welded loops that can break off. It should hold up to anything an ATV is capable of towing, and it fits snugly in my ATV’s receiver.
William Shepherd
Reviewed in the United States on October 22, 2020
Very well engineered and solidly made to handle all the hauling needs for my utility vehicle.
Glenn
Reviewed in the United States on December 31, 2018
I haven't had a chance to put this through it's paces yet, but just by looking at it, I think I'd twist the frame of my wheeler before I'd manage to break this thing. It looks really solid, and more than adequate for anything a wheeler would pull. The receiver material is a little thinner than what you'd find in a standard vehicle receiver, so while plenty strong for a wheeler, it's noticeably lighter than a heavy duty truck receiver, which is great.There isn't much room between the 2 holes, so I'd recommend a ball like the one in my pic, and mounted so the flats are to the front/back. That way there's a little extra room for swing of whatever implement you're attaching. A portable ice house tongue is what's in my pic, and was the initial purpose for this purchase, although I'm sure I'll use it for much more in the future. I used an extra 1/2" receiver pin from my car, and it's a small enough diameter to wobble in the hole just enough for the tongue to tilt over the snow, ramps, etc.For Christmas, I got a KFI snatch block, and a Smittybilt 1/2" bow shackle. The pin diameter of the shackle is a perfect fit in the accessory hole, as seen in the other pic. It should come in handy on the trail, for snatching or towing, etc., and will serve much better than just tossing a strap over the ball.As far as the hole spacing goes, if there were more room between the holes, then it would stand a good chance of bottoming out on a trailer frame. I hitched up the 5x8 utility trailer I haul my wheeler on so I could go park it, and there's just enough clearance between the receiver and the trailer frame, so any longer for more hole spacing, and there could be problems.I do kind of wish the plate were a little longer, and welded on further out, so the receiver could be mounted upside down for a little drop in ball height, but that might mean an even heavier plate, so I'm not sure if that would work or not. As it is, if the ball is mounted on the bottom, the ball is too close to the receiver bar for the trailer coupler to fit over the ball.Oh, and besides the decal and card, mine also came with a Feral pen! No biggie, but it was a nice touch!
Harri
Reviewed in the United States on October 18, 2018
This 2" hitch receiver and FERAL 2" x 6" Spread Eagle 3- Hitch is perfect for my ATV! Strong mount and excellent quality! I have used it several times with a small trailer and it works great!
Steve M.
Reviewed in the United States on February 4, 2017
Beautiful product, proudly made in the USA. Smooth finish, nice welds. Will be using this to pull a leaf collector on my Kubota.
Recommended Products
