Your cart is empty.
Your cart is empty.
Specifications:
The 2-way power distribution block allows you to connect as many as three amplifiers to a single power source. The main input lets you connect 4 or 1/0 Gauge wire from your battery to the block, and you can run up to three 4-Gauge or 8-Gauge wires to your amplifiers.
Type: 1 Way In 2 Ways Out power Distribution block
Distribution Block Weight:90g
Size:45 x 40 x 28mm/1.77" x 1.57" x 1.1''" (L*W*H)
Screw-down Wire Clamps
Input: 0GA/2GA/4GA Gauge Wire
Outputs: 4GA/8GA/10GA Gauge Wire
Impact Resistant Snap-on Plastic Cover
Platinum-Plated for Corrosion Resistance
Offers complete protection for your car audio system
Note:
For your vehicle’s protection, it is better to put an inline fuse holder between the distribution block and your vehicle’s battery.It can also be used to combine the ground wires of multiple amplifiers to a single grounding point.
Package included:
1 x 2 Way Car Power Distributor Block Holder
PJ Ferris
Reviewed in the United States on January 16, 2025
Don't over tighten the the wires fastening bolts. They can strip the threads if you tighten too hard.
Rab
Reviewed in the United Kingdom on January 15, 2025
Came next day no problems
Sadie Thatcher
Reviewed in the United States on July 25, 2024
Exactly what I needed!!!
Todd ( Tj ) Jones
Reviewed in the United States on February 22, 2024
Recommend to all great product
J. E. Lee
Reviewed in the United States on February 13, 2024
It did what I wanted.
MR ROBERT SMITH
Reviewed in the United Kingdom on August 30, 2023
I have used two of these as part of a custom boot installation with 4awg going in and out to the amplifier, and then a 20awg cable for the DSP unit without issue. I would prefer if it was sold with ferrule rings to make clean and safer connections, but they are available to purchase elsewhere separtely. The units feel well made and the threaded clamp points are strong.
AJ
Reviewed in the United Kingdom on December 10, 2022
Works well and very decent quality product
TBert
Reviewed in the United States on May 21, 2021
Good quality and easy to install. Used two of these for an audio install on a boat. Ran 4 gauge from the battery’s negative and positive and fed two amps; one with 8 gauge and one with 10 gauge. Worked great.
M
Reviewed in the United States on April 14, 2021
Used two of these, one for power and one for ground 12V distribution in a Transit van camper conversion for solar, inverter, alternator, and light, pump and fridge loads. Did have to be careful with the aluminum solar power cables as it tended to break off the wires when screwing them in but got it figured out by removing only the face of the insulation then works perfectly.
Joseph b
Reviewed in the United States on September 26, 2020
Im running 3 amps in my truck, so this product is perfect. With multiple amps you dont want multiple power supply wires. With this product you only need 1 power supply wire. With this product I am running a 2 gauge from the battery and splits to a 4 gauge, and 2 - 6 gauge to my amps instead of 3 wires from the battery to the amps,... which by the way is not good for your battery or sound. I find it works great. Very easy to install, its not rocket science.
Gioele.
Reviewed in Italy on June 17, 2020
Ottimo, tutto ok!
larry eaton
Reviewed in the United States on December 16, 2020
This is a very heavy duty distribution block, probably for big sound systems where you use 00 wire. Worked for me using #14 wire, just over kill for my application. Great value!
Salvador
Reviewed in Spain on October 2, 2020
El artículo va perfecto y no es de un gran tamaño! Lo aconsejo!
Recommended Products
