Shopping Cart

Your cart is empty.

Your cart is empty.

2 Pack 62-24164-01 Furnace Burner Ignitors Repalcement, Flame Sensor Ignitors with 232258 2-Prong Electrode Assembly and 31.5' High-Temperature Cable Wire Compatible with Rheem Furnace

4.7 (3) Write Review
Free shipping on orders over $29.99

$16.99

$ 7 .99 $7.99

In Stock
  • [𝐏𝐑𝐄𝐌𝐈𝐔𝐌 𝐌𝐀𝐓𝐄𝐑𝐈𝐀𝐋]: Our 62-24164-01 flame sensor igniter replacement for Rheem furnace is composed of 2-prong metallic electrode, ceramic insulator body, 31.5" 480°F high-temperature rubber cable wire. This can be universal kit if you can adjust the height of spark pin in right position. The two pin will increase the power during spark and higher efficiency ignition.
  • [𝐅𝐔𝐍𝐂𝐓𝐈𝐎𝐍]: This 62-24164-01 direct spark ignitor replacement is designed to monitor and verify whether a flame is burning inside the furnace. The flame sensor is a safety component of a furnace located on the interior of the burner assembly.
  • [𝐖𝐈𝐃𝐄 𝐀𝐏𝐏𝐋𝐈𝐂𝐀𝐓𝐈𝐎𝐍]: Our gas furnace flame sensor ignitor replacement for rheem also can be used for any propane or natural ignitor system like grill, fire pit and water heater if you can adjust the height of the sparking area to fit your burner.
  • [𝐄𝐀𝐒𝐘 𝐓𝐎 𝐈𝐍𝐒𝐓𝐀𝐋𝐋]: Before installation, it is important to shut off the power to your furnace (or any other appliance), then remove the broken sensor and replace our 62-24164-01 flame sensor ignitor replacement for Reheem's water heaters furnace, finnally turn the power back on and check the results.
  • [𝐏𝐀𝐂𝐊𝐀𝐆𝐄 𝐈𝐍𝐂𝐋𝐔𝐃𝐄𝐃]: You will receive 2 pack 62-24164-01 flame sensor igniters replacement Rheem furnace with 232258 2-prong electrode assembly and 31.5" 480°F high-temperature rubber cable wire. The cable with terminal fits the electrode terminal and other side with rough 2.3mm terminals. Any question on product, feel feel to contact us, we will reach you at the soonest.


Product Description

62-24164-01 Furnace Burner Ignitors
62-24164-01 Furnace Burner Ignitors
62-24164-01 Furnace Burner Ignitors
62-24164-01 Furnace Burner Ignitors

NR
Reviewed in the United States on January 23, 2025
Bought the 2 pack one of them works perfectly fine the other is faulty and still not sensing flame. Once wiped down it senses flame for about 6 hrs and its back to being cold in the house.
Moses Collins
Reviewed in the United States on January 17, 2025
This replacement sensor is working perfectly for us.
BSLAWS
Reviewed in the United States on November 14, 2022
The OEM ignitor's wire was permanently attached to the ignitor. The end that attaches to the ignition coil is pretty flimsy and I had to use plies to close the connector so it would make a good connection. Time will tell if it will last as long as the OEM unit. These were $7 each at the time of purchase so I can't really complain.