Your cart is empty.
Your cart is empty.YUNGUI 15 Pieces 5X7cm 1-2-3 Joint Hole Strip DIY Soldering PCB Protoboard Circuit Board Stripboard for Electronic Project and Electronic Experiment
Features
Includes 15pcs 5x7cm blank 1-2-3 Joint Hole PCB stripboard.
Electronic parts and Electronic equipment replaced and Repaired include: LCD Modules, Optoelectronic Displays, Capacitors , Resistors ,
Potentiometers , LED Displays , Electronic Accessories & Supplies,Electronics Stocks,Ative Compent , Integrated circuit , Diode , Transistor.
Product Description
Quantity: 15pcs
Size:5X7cm
Specifications: single-sided
Thickness: about 1.2mm
Pitch:2.54mm
Hole diameter:1.0mm
Material: Bakelite
Package List
15pcs 5x7cm Circuit Stripboards
virtuosomaximoso
Reviewed in the United States on February 21, 2025
The pads are pretty weak to thicker wire and heat. Otherwise pretty good. I think I'd like the straps to connect across horizontally to the edge, but the 2 pads on the side work well for connecting items where you want.
Great brush is very soft.
Reviewed in the United States on July 29, 2024
As described.
Pedro
Reviewed in the United States on March 4, 2024
Lets start with the cons, which should be obvious, but since people are confused: No, these are not plated through hole PCBs. Yes, soldering on them will be different than through hole PCBs since the solder won't wick through. You won't get the mechanical strength you will from plated through holes. But these are cheap, you get what you pay for.That said, these are great for small projects and beginners. Spacing is good so it's hard to bridge. Holes are drilled out well. Layout is good for DIPs. I haven't had any problems with lifting pads, but I wouldn't be surprised if it's hard to desolder since they're not plated holes. So far they're working for me. Just wish we had dimensions for mounting holes.
James Gilbert
Reviewed in the United States on December 5, 2024
Easy to solder DIP components or packages with leads. Will buy again if I need more for another project.
Brian Tamburelli
Reviewed in the United States on November 19, 2024
I like how these are patterned out like a breadboard! Great addition to my Electronics Laboratory Bench!
DMK
Reviewed in the United States on August 15, 2023
one sided board with two vertical rails in the center, and tri-node paths near the dip in center. toward the outer edges, they are single net pads. Single sided, and holes are not plated. 0.1 inch centers. great little board for breadboards using DIP and Thru-hole components.
Douglas W.
Reviewed in the United States on July 23, 2023
I am a hobbyist board repair and retro game console modder. I picked these up because they had various trace connections lengths and orientations and I thought it would reduce the amount of jumper wires I would need to solder with other breadboard style prototype boards that are just rows of traces.I see (3) main issues with these boards. I can see these being a huge problem for beginners and for that would not recommend it for beginners or anyone who hasn't soldered in awhile.1. As others have mentioned the traces do not go all the way through so that somewhat reduces the utility that I gained with other boards, but I worked out a system to help here. I would keep the leads long on some components so I can pass them through then back up into another section. This requires a lot more planning ahead of time though.note: if you do get these, make sure you put the components on the side without the trace so you can solder them, then cut off the extra lead.2. Again as others have mentioned, the trace quality and mounting is poor and they don't take to heat very well. To counter this I cranked the heat up on my iron to ~800F to get a good solder. The problem with this is that at that temperature, its much easier to burn the board and/or traces and destroy them. For beginners this can be a challenge because this means you need to be good with flux and solder application to quickly get it locked in and not cause damage.3. I think this was also mentioned too, but the way the solder flows on the trace bars isn't great (which is why I raised temperature), but this also causes problems when trying to keep the solder over one of the holes and not flow to surrounding holes.The first three pics are of me using this board, and the last 2 are me using a breadboard style board. You can see a clear difference in quality of solder joints. Both of these boards are the same circuit with differing design and components.
John
Reviewed in the United States on October 19, 2020
these boards are really low quality. the pads have no through vias so only one side can be soldered. the pads are also very weak and tear off with any stress. boards are also coated in some slightly tacky substance which burns very easily. would not recommend. the pad arrangement is also quite annoying.
Recommended Products
