Your cart is empty.
Your cart is empty. 2-Pin Motorcycle and Car Speed Adjustable LED Turn Signal Indicator Hyper Flasher Relay.
This 2-pin Electronic LED Flasher is also speed adjustable.
Universal fit for many vehicles that use a 2-Prong (2PIN) flasher with a socket wired to SAE specifications.
Fit for Ha-ly Dv-dsn,Ho-d,Ka-k,Su-zk,Ya-h and many other brands as well.
Connection and adjustment Instructions:
Clockwise: slower, Counter Clockwise: Faster
You can use a flat head screw driver to adjust the knob on the bottom to set its flashing speeds from 50c/m to 200c/m .
EASY to install the LED bulbs for the car and motorcycle for turn signal lights without having to cut the wires to install the load resistors, completely eliminate the LED rapid flashing problems. Using advanced SMD chip technology,with automatic short circuit protection, automatic overload protection, reverse polarity protection automatically.Allow more stable LED work.
Tips:
1.If the flashing speed is not up to the individual requirements , flicker frequency can be adjusted to achieve the speed of requirement by adjusting the switch on the relay 2 pins flasher relay, can be fitted on most of motorcycle and car or any custom application .
2.Great for replacing a bad relay or correcting led turn signal problems (fast Flashing, no flashing).
3.Replace the stock relay in the fuse box. Please check your owner manual to locate the flasher. Pin B is power in, and Pin L is the adjustable power out.
Vance
Reviewed in the United States on January 14, 2025
Worked great with LED bulbs in my 1972 Chevrolet El Camino. Don’t buy the cheaper ones, they don’t work.
Lloyd Anderson
Reviewed in the United States on September 5, 2024
For one reason or another the turn signals on my wife's Sportster stopped blinking and just stayed steady. After watching a YouTube video it was recommended that I install one of these for each side of the turn signal. The only thing I would say is that I can't get them to sync to the exact same speed but you would never know since you can't turn both turn signals on at the same time.
J.Hall
Reviewed in the United States on February 20, 2024
A plug and play install and it works great.
Bud
Reviewed in the United States on December 13, 2024
Used to replace Honda turn signal flasher unit at about 1/2 the price. Fully adjustable flash speed and looked to be very well-made. I would recommend. Thanks, Amazon. -Bud
Erin fox
Reviewed in the United States on October 4, 2024
Fits 2003 honda rebel cmx250 perfect and works even with led rear lights as it should.
Jennifer Bishop
Reviewed in the United States on October 12, 2024
I installed a pair of LED lamps on the back of my tractor for safety purposes and ordered this flasher for high visibility. I get one bright flash when connecting the power, and then they just glow dimly. Bottom line is that this flasher does not work for LED lights, so I will have to buy another. I would not suggest anyone buy this who plan on flashing LED lamps for any application.
Amanda Perry
Reviewed in the United States on August 4, 2023
I just installed this in my 66 El Camino. I recently purchased super bright LED bulbs for my tail lights/ blinkers and back up lights. Turns out the blinker bulbs were not compatible with the old style flasher, thus no blinker function. So I found this LED compatible flasher for a nominal price and ordered it. I just installed it. It fit perfectly on the receptacle under the dash, and works like a charm. I like the adjustable blink rate too. I can’t speak for the longevity of the flasher, because I just installed it. So far I’m very happy that it resolved my non blinking signal lights.
Leroy W.
Reviewed in the United States on November 20, 2023
I used this flasher for a 2010 Crown Victoria. I had struggled with hyper flashing when I changed to LED turn signals and canbus LEDS did not work. Since non of the flasher st autozone worked as well I had to go with this one.I did not try the flasher speed feature as the stock speed was fine.If your going to use for the Crown Victoria, I would suggest using the wiring harness for the turn signal stock. You will need to remove the plastic pieces on the steering wheel. The connector should be directly behind the 4 way flasher buttons. Your going to need the solid light blue and the red with white strip wires. The Red with white stripe wire is theb12v constant and the blue will be the load. This requires more plastic to remove to get too in comparison to the Light module. However you have more access to the wiring this way as well and it's more friendly as you don't have to be at awkward angles for the lCM in the footwell
Recommended Products
