Shopping Cart

Your cart is empty.

Your cart is empty.

12Pcs Trimmer Potentiometer Sensor Replacement for Xbox One,PS3,PS4 Switch Pro Controllers,Trim Pot Resistors Repair Parts for Thumb Stick Analog Joystick

Free shipping on orders over $29.99

$8.49

$ 4 .99 $4.99

In Stock
  • Useful:The 3Pin trimmer potentiometer sensor needs to be replaced when the controller has the problem of creeping, stuttering, a blind spot, a dead spot, a dead zone or wouldn't center after years of wear and tear.Soldering the unit with only 3 prongs will be much more easier than replacing the 14Pin joystick assembly.
  • Used for:The trim pot resistor is OEM repair parts, the same model as the one in your controller. The genuine replacement sensor is to ensure accuracy and prolong lifespan. replacement for the wireless controllers below: PS3; PS4 DualShock4 series (PS4, PS4 Slim, PS4 Pro); Xbox One series (Xbox One, One S, One X and Elite); Nintendo Switch Pro controller.
  • Note:Make sure you have basic soldering skills and some soldering supplies like an electronics solder iron and small gauge solder. Use a pair of pliers to separate the problem sensor off the thumbstick component. A metal pick helps to clear the holes in the PCB. Re-soldering the new unit in is a breeze. Just remember to use flux and keep the iron's tip well tinned.
  • Package include: 12Pcs potentiometer sensor modules for games controller joystick.


Compatibility:
1.Fit the wireless controllers below: PS3; PS4 DualShock4 series (PS4, PS4 Slim, PS4 Pro); Xbox One series (Xbox One, One S, One X and Elite); Nintendo Switch Pro controller
2.We can't sure whether its compatibility with other controllers. Please check the sizing and make sure it is around 10K ohm
3.It will solve the problems caused by the 3Pin sensor only,It will not deal with other problems that caused by other parts like the tactile switch. Make sure this point before ordering

Package include:
12Pcs 10K ohm Trimmer Potentiometer Sensor


Darth Valenti
Reviewed in the United States on January 30, 2024
So many controllers that have been put to the side or discarded can be revived with this simple part. It's so nice not to be constantly drifting to the left!
Rob L
Reviewed in the United States on December 18, 2023
Followed the instructions to replace sensor without having to re-solder and my controller is as good as new. No idea how long they will last but they are cheap/easy enough. I tested my controller as I was switching them out and found I didn't even need to replace all 4 to fix stick drift.
Dominik
Reviewed in the United Arab Emirates on October 22, 2023
They are ok, even can be mixed with original resistors on the same stick. But their response off the centre is much faster than the original Xbox or PlayStation resistors. Good for direction thumbstick but bad for aiming.
Customer
Reviewed in the United States on January 6, 2023
Fixed my stick drift. Worked exactly as shown with no soldering needed unless you accidentally pull something off. Put my nearly unusable elite series 2 controller back to 100%.
Queze
Reviewed in the United States on April 14, 2023
They don’t work!!!
Billie Jo
Reviewed in the United States on May 30, 2022
These are not the same quality as always OEM at least the original from MS last about a week past the 6-month warranty. Installed this three times already in same controller, pretty soon The motherboard will be worn out. They only last 7 to 10 days. Save your money and buy the extended warranty on a new controller.
B
Reviewed in the United States on September 7, 2021
I tried using these to replace a set of potentiometers on a Dualshock 4. According to my testing via GamePad-Tester.com, the replacement potentiometers are only half as accurate as the original Alps brand potentiometers. These replacements will do in a pinch, but you'll be better off detail cleaning your original Alps potentiometers instead, if you have that option.
Recommended Products

$12.99

$ 6 .99 $6.99

4.5
Select Option