Your cart is empty.
Your cart is empty.Product Description
Hot Wire Cutiing Machine
The hot wire foam cutting machine is made of high-quality wood and stainless steel, which are strong, durable, not easy to deform, and not easy to rust.
Foam Cutter
WIDE APPLICATION
It can be used to cut foam, sponge, pearl cotton, ribbon, KT board, etc. It can cut angles, cylinders, sharp cones, rings, cones, straight lines, and other shapes.
Hot Wire Cutter
Foam Cutter
Our foam cutting machine injects new efficiency and convenience into your creative process, saving valuable time and energy dramatically. It reshapes the boundaries of creativity with precise temperature control and diverse adjustable designs. Simple operation allows ideas to be realized immediately. By choosing this product, you are embracing a more efficient, precise and innovative approach full of endless possibilities.
- Good Materials
- High Efficiency
- Adjustable Voltage
- Adjustable Support
- Precise Cutting
KEY FEATURES
Wide Adjustable Angle
The Stainless Steel column supports 180° adjustment,The direction of heating the tungsten wire can be changed ai will.
Round-cutting Aid
The round-cutting aid can assist in round-cutting, and the cut-out circle is more regular, which can make cutting more convenient.
Wide Application
can be cut foam,low-density sponge,pearl cotton,KT board,extruded board and other Materials.
Precise Measurement
The worktable is thoughtfully designed with scales on all four sides making it easy for you to accurately measure each piece of material. The 0.01in heating wire design allows for more accurate cutting and less error, as well as a lower loss ratio.
How to Install
1. Take out the semicircular angle board, align two holes on the angle board with two holes on the worktable, and tighten them with screws.
2. Take out the L-type stainless steel square pipe support, and align two holes on the pillar with two holes on the angle board. Put on the bolt, cover the copper nose (copper nose is conductive zero line, and very important), and tighten the nut.
3. Pull out the heating wire about 30cm/11.81in from the wire wheel.
4. Thread the heating wire through the small hole of the worktable, and then make a ring on the heating wire and hang it on the spring at the machine's bottom. It should not fall off.
5. Rotate the aluminum alloy wire wheel on the bracket to tighten the heating wire. The heating wire is moderately tight and naturally elastic.
Nelbert
Reviewed in the United States on January 7, 2025
Pros:It's (relatively) cheap, and if you scour the internet, you'll find videos for other similar products that more adequately explain the setup process.Cons: The power supply works intermittently, usually needing to be turned on and off several times followed by a good wack, and even then, it goes off randomly when set below an output of 10V. I'm hoping that a new power supply ordered from a different vendor will prove more useful.But this assumes one actually manages to construct the device, a task not facilitated by the minimalist instructions. Steps 1 through 3 are simple, but step 4 simply states, "The electrothermal wire is hung on the spring and should not come off" below a picture of the table underside in which no wire is attached to the spring. What the instructions leave out is that one needs to unwind a length of wire from the spool attached to the pillar, feed it through the hole in the table, twist it around the open end of the spring, and then take up the wire slack by dialing back the spool, making the wire taut but not too taut. If the overall product were better, the poor instructions wouldn't be much of an issue, but as is, it underscores how cheaply made the whole product is.
The_Warpact
Reviewed in the United States on March 16, 2024
Use this for foam cutting in miniature terrain. It does the job and cuts quick.
hevanslight
Reviewed in the United States on March 1, 2024
Have not yet used but am excited to get going.
Marc Penso
Reviewed in the United States on December 11, 2024
I had made one before myself ten years ago from plans, but I wanted something ready to go. Easy to assemble. I like that the voltage is variable and shows you the number digitally. If you turn it up the wire gets red hot real fast! I didn’t need it very hot. Cutting pink foam used for insulation for a project, worked perfectly (not used for insulation). Very good product for the money spent!
Gloria Z.
Reviewed in the United States on October 10, 2024
Seller:I was initially disappointed with my initial set-up attempt because it seemed there was a misalignment of a part. I reread the instructions which include photos, but still could not get it align. I submitted a return request. That evening the seller messaged me and asked for photos of the parts, which I sent. I appreciated seller reaching out so promptly. Next morning I received more images and detailed instructions. I immediately saw it was my mistake. Ugh! I proceeded with setup and it is working beautifully. This seller knows about good customer service!Product:Well made and easy to set-up (if unlike me, you follow instructions correctly). The only con I have is that end of the guiding ruler scrapes my nails when I turn the tightening screw. I think it's an easy fix though, a little filing down or a piece of tape on the offending corner and it should be good.I am happy with the product and impressed with the seller's customer service.
coco
Reviewed in the United States on December 31, 2023
I use it for cutting foam for my projects and also for cutting satin ribbon and it works great heats up fast
Recommended Products