Your cart is empty.
Your cart is empty.
Specifications:
Cutting Diameter: 1/4", 5/16", 3/8", 1/2"
Cutting Height(Approx.):25/32", 63/64", 1-3/16", 1-3/16"
Cutting Height: 20mm, 26mm, 30.7mm, 30.7mm [Metric measurement results are accurate.]
Safty and Efficiency :Blade Material: YG6 carbide; Body Material: 45# carbon steel,high performance, cutting sharper
Bits Set, 1/4 Inch Shank, Bottom Bearing Pattern Router bit Set
Customer
Reviewed in the United States on August 26, 2024
It worked good for the money a very good deal
Thomas Allhoff
Reviewed in the United States on June 24, 2024
I liked these a lot, good steel and when I used them repeatedly in tough grain oak they held up better that I hoped.
Bob_Sunshine
Reviewed in the United States on September 5, 2023
These bits are very inexpensive with a corresponding production quality. I made some flush cuts, grooves and dados in some white pine. I made some similar cuts in red oak. The results were ok, but had some issues with a little tear-out. and rough sides for flush cuts and grooves. Some touchup finishing required.The bottoms of grooves and dados were nice and flat. All the cuts in oak were much better. Of course this is which new sharp blades. I will use these for rough projects, saving my spiral bits for finer work.The info page lists using this in chipboard and plywood. I also did some cuts in OSB with, as expected, pretty poor results. One might use these to make dados in plywood for say a bookshelf. These dados were acceptable, with only a minor amount of chipping.This set would be a reasonable choice for a beginner interested in accumulating a variety of bits. As your experience and skills progress, replace the ones you really use with better quality.
Danny P
Reviewed in the United States on September 25, 2023
For the price, I honestly had very low expectations for these bits, but figured I'd give them a try. Anything to save money these days, right? They're just going to live in my tool box and be used in my little battery powered palm router anyway. I have to say, I'm very pleasantly surprised. I normally subscribe to the "buy once, cry once" school of thought, and most of my bits are red in color and share a name with a famous psychologist. You wont hear me arguing that these are "just as good" as German or Italian cutters are, they do have a few cosmetic blemishes, but they cut just fine. No runout, no chattering, no burning... just cutting. A set of 4 for less than half the cost of a single bit from the name brand? 5 stars in my book, even if they may not last quite as long (which in fairness remains to be seen).
Matt
Reviewed in the United States on September 21, 2023
I quite like this bit set!The bits themselves seem to be well made. They are all sharp, with even sharpening along the whole length of each flute. A quick check with some calipers shows them to be reasonably precisely manufactured, as well. I don't see any signs of rust or oxidation on the metal, either (and nor should you ever, but you never know and so it's always something I at least look for with a quick glance).Overall, I think this is a really useful set to have for somebody with a home workshop.
Alan Wolf
Reviewed in the United States on September 1, 2023
Each bit comes in its own holder. I tried the 1/4 inch and 1/2 inch into some scrap maple to get a sense of how they cut—and both bits did a fine job. I am hesitant to give 5 stars on a cutting tool until I've had it long enough to get a sense of how good the alloy on the cutting portion is. These came nice and sharp, and appear well made, not even considering their low cost.I don't use this style of bit that often, but obviously, when you need it, you need it. If, after further use, I feel that the se bits did not perform that well, I will update my review.
Tim Hall
Reviewed in the United States on December 3, 2023
Good, but not great it’s not something I would want to take to work and use all day long, but for one or two quick projects, not bad for the money.
Mulkerns ❤️
Reviewed in the United States on November 21, 2023
1st, the Price is right! I had a project that I planned on using these with but it's been delayed. I did a swirl in a scrap piece of wood to test them out. I'm happy and I'm sure once I start really putting them to the test they'll have me satisfied
Recommended Products
