Your cart is empty.
Your cart is empty.Product Description
ITEQ 6 Point 7/8 inch (22mm) Offset Oxygen Sensor Socket
- Perfect for removing, inspecting, replacing and installing heated and non heated oxygen sensors found on most vehicles
- 6 point hex and slotted design enables the socket to be fitted over wiring harness, offset and compact allows for extra leverage in hard to reach spots
- Construction of chrome vanadium steel for extra strength and durability
7/8" and 1/2" Drive
7/8 inch hexagon head drive and 1/2 inch square drive can be used with both ratchet wrench and breaker bar
- The double-drive design and 90 mm long provides extra leverage in using
- It can be used in most oxygen sensors and even in hard-to-reach spots
- Make the job much easier and save time
6 Point 7/8 inch Hex and Slotted Design
The ITEQ 6 Point 7/8 inch (22mm) Offset Oxygen Sensor Socket features a wire gate access cut-out design, so you can easily removing or installing the oxygen sensors without damaging the wiring harness.
The 6 point 7/8 inch hex is suitable for almost all oxygen sensors.
- Wire gate access cut-out design
- 6 point 7/8 inch (22mm) hex socket
- Prevent damage to the wiring harness
Universal Compatible
The ITEQ Oxygen Sensor Socket is compatible with all computer controlled engine vehicles and some motorcycles with a 7/8” hexagon nut oxygen sensor
mark
Reviewed in the United States on September 8, 2024
perfect fit worked great.
Customer
Reviewed in the United States on August 8, 2024
Could not remove sensors . Tool kept spreading open when trying to remove part.
Daniel Smith
Reviewed in the United States on July 27, 2024
I tried to remove a 22mm o2 sensor with this socket, and it flexed and twisted so badly it was about to break, it is nowhere near strong enough for removal. I ended up cutting off the wires and used my regular 22mm socket, the old sensor came loose easily. On the bright side, I was able to use this weak o2 sensor socket to install the new sensor, since it required minimal torque. The fact that they made the o2 socket with an unnecessarily wide 5/8" gap to clear the wires certainly weakens it, but the steel they used is poor quality regardless. It's not worth my time to return this thing, and it was inexpensive, so I'll keep it to use for installs only. lol Get what you pay for.
rhvic
Reviewed in Canada on July 18, 2024
This will work well if you do not have to apply too much force to the sensor to get it loose; otherwise the socket has a tendency to deform a bit and you may have to apply some force to the socket to get it to let go of the sensor. Reasonable for the price.
Dane
Reviewed in the United States on June 23, 2024
Great quality. Needed in order to change out the 02 sensors on my Hummer H3
TBrown
Reviewed in the United States on May 23, 2024
The way the slot is cut on the deep socket works great for sensors that have wires in them
Dale C.
Reviewed in Canada on December 8, 2024
Used for taking o2 sensor out of exhaust on my titian arrived on time perfect
Patrick
Reviewed in Canada on November 3, 2024
Bought this to remove a stuck O2 sensor. Didn't work. There is too much flex and the end of the socket opens and eats the corners of the nut on the sensor. Might work on a less stuck sensor but then so would a regular open wrench.
Mario
Reviewed in Canada on November 19, 2024
Très utile
GoFish
Reviewed in Canada on November 16, 2024
Worked for me, and got the job done.. :)
B. Groves
Reviewed in the United States on September 7, 2023
I'm not sure why you make it so thin walled as that's normally an area of difficulty on most sensors except to save money??Their thin design deforms and jumps to the next set of flats on the sensor somewhat rounding off the corners to make removal with a decent wrench more questionable.The only use I see this suitable for would be installing a new sensor in a fresh clean bung but removing a sensor not that badly seized good luck.Disappointed 😞
melonhed
Reviewed in the United States on March 20, 2023
The media could not be loaded.
S C
Reviewed in the United States on December 27, 2023
At $9.99 - $10.99, this is a good buy. It helped replacing the fuel/air sensor of 2011 Honda CRV. Use of a 1/2" drive 24" long handle breaker bar is recommended. Please, spray WD-40 and wait for 4 hours of so prior to an attempt to remove the fuel/air or oxygen sensor. Hurry upping may result in a real mess with a deformed Fuel/Air sensor still stuck on the bung.
Recommended Products