Your cart is empty.
Your cart is empty.R8 Collet & Tool Tray This Convenient Tray Will Cut Down Set Up And Tool Changing Time. Operator Works More Organized. Easy To Install, Drill And Tap Two Holes In The Base Casting 1" Below The Degree Ring.
Jacob B.
Reviewed in the United States on November 6, 2024
Fit my bridgeport j head fine it requires drilling and tapping 2 holes in the base casting to mount it which shouldn't be an issue for anyone purchasing one of these. Feels a little cheaply made(I believe its cast aluminum) but it has been holding up fine so far. As long as you don't overload it with extra stuff I don't expect it to break. Its been holding a whole set of collets, a annular cutter adapter, and a keyless drill bit chuck for close to a year now with no issues
Jacob B.
Reviewed in the United States on November 6, 2024
Fit my bridgeport j head fine it requires drilling and tapping 2 holes in the base casting to mount it which shouldn't be an issue for anyone purchasing one of these. Feels a little cheaply made(I believe its cast aluminum) but it has been holding up fine so far. As long as you don't overload it with extra stuff I don't expect it to break. Its been holding a whole set of collets, a annular cutter adapter, and a keyless drill bit chuck for close to a year now with no issues
Larry
Reviewed in the United States on November 3, 2023
Not anodized as picture shows. Cheap flat black paint easily scratched.
Larry
Reviewed in the United States on November 3, 2023
Not anodized as picture shows. Cheap flat black paint easily scratched.
Ron Rhodes
Reviewed in the United States on September 17, 2022
Planed on mounting on a flat board. Was obviously intended to mount on a curved surface. Definitely not for a mini mill
Ron Rhodes
Reviewed in the United States on September 17, 2022
Planed on mounting on a flat board. Was obviously intended to mount on a curved surface. Definitely not for a mini mill
P. Sullivan
Reviewed in the United States on November 22, 2022
I needed a collet holder, and I was going to make one from scratch. When I saw the price on this unit, SOLD! To be fair, I did have to machine the mounting surfaces, 2 of them, so it sat on the Bridgeport body, but as a machinist, that was simple. It mounts up nicely, holds my most used collets, PERFECT!
P. Sullivan
Reviewed in the United States on November 22, 2022
I needed a collet holder, and I was going to make one from scratch. When I saw the price on this unit, SOLD! To be fair, I did have to machine the mounting surfaces, 2 of them, so it sat on the Bridgeport body, but as a machinist, that was simple. It mounts up nicely, holds my most used collets, PERFECT!
Jason N.
Reviewed in the United States on August 16, 2021
This little ditty is not too bad, but its not perfect either. The feet the mount it need to be massaged to mate up cleanly to the surface of a mill stand. This should not be needed due to the fact that any mill that is not a Bridgeport is a copy of a Bridgeport. It should be design intent that it mount directly to the mill stand, but you can massage it with a grinder, or a boring head if you have the time and gumption.
Jason N.
Reviewed in the United States on August 16, 2021
This little ditty is not too bad, but its not perfect either. The feet the mount it need to be massaged to mate up cleanly to the surface of a mill stand. This should not be needed due to the fact that any mill that is not a Bridgeport is a copy of a Bridgeport. It should be design intent that it mount directly to the mill stand, but you can massage it with a grinder, or a boring head if you have the time and gumption.
Shop owner
Reviewed in the United States on April 21, 2017
It's just an ok part. I had to grind and reshape the mounting ears to fit my mill base. The back holes to rack the collets are spaced to close together and the collets run into each other. A bit more spacing would have worked. All in all it'll work fine to organize what I have.
Shop owner
Reviewed in the United States on April 21, 2017
It's just an ok part. I had to grind and reshape the mounting ears to fit my mill base. The back holes to rack the collets are spaced to close together and the collets run into each other. A bit more spacing would have worked. All in all it'll work fine to organize what I have.
Tina
Reviewed in the United States on May 12, 2016
Works great
Tina
Reviewed in the United States on May 12, 2016
Works great
Spider Monkey
Reviewed in the United States on November 6, 2014
Works well
Spider Monkey
Reviewed in the United States on November 6, 2014
Works well
Recommended Products
$22.39
$ 11 .99 $11.99