Your cart is empty.
Your cart is empty. BOJACK High Quality Toggle Switch
MODEL:RT1221
Switch Type: ON - OFF
Connector type: DPST / 4 Terminal Pin
Mounting hole diameter: 12 mm/0.47 inch
Total Size :34.6x 19.5 x 56 mm / 1.36 x 0.77 x2.21 inch(L*W*H)
The toggle switch is widely used in electric power, chemical, printing,
textile and other industrial fields, and hotels, automobiles, fans,
and other life appliances.
celestial
Reviewed in the United States on March 11, 2025
Switches are nice they're easily to disassemble and reassemble they are independent sighted so you can run positive and negative through either side would recommend these switches to anybody long as you wouldn't using them in environments that could get wet because they are not waterproof in any way
Turbodog1000
Reviewed in the United States on January 22, 2025
Worked just like I needed.
Tom Sendelbeck
Reviewed in the United States on January 21, 2025
These do have plastic backs, not steel. The steel backed ones are more industrial, but you have to pay the price and work to find them. This one worked well for my application, and I can get rough on things. So far it is working well.
Tony S
Reviewed in the United States on January 17, 2025
Installed into our 240 volt parts washer, and it working just fine.
Bad Habits Lounge Studio
Reviewed in the United States on August 5, 2024
Although these switches are rated for high voltage, I'm using them as speaker switches - They work great!
MoonDoggy
Reviewed in the United States on July 7, 2024
I am using this DPDT switch as a mini Manual Transfer Switch for an RV rooftop A/C unit. I have two power sources GEN and Shore that I select from. This MTS will prevent power feedback when in a Generator Mode condition. The common output is a Furrion 15kHE rooftop A/C that draws a constant 14A on high fan speed (full bore). Nominally, 20A circuits would be either #10 or #12 wires. The Generator feed is #14 via a separate barrel selector switch. Since the draw is 14A then #14 wire is ok.Case in point, These screw type terminals are very small in size(maybe as small as size 4 screw). To connect anything larger than a #16-#14 gauge wire requires a lug. Currently, I am using small yellow lugs that are mechanically crimped to the interface wires. I have taken and extra step isolating each contact with 3/8in silicon rubber tubing.I can safely state that the connections do get warm after running the A/C unit steady over time. I can also recommend some kind of lock washer or even better a star washer to keep these connections tight even after warming up and cooling down.Like I mentioned, these do work but may look into a Gardner Bender version that appears to have a larger contact surface area to support 12/2 and 14/2 electrical wirs. The TTHN #10 wire will still need lugs.The front end to this DPDT will have a Tyco W31-X2M1G-20 20 Amp Circuit Breaker Switch from the shore power feed circuit.
William A.
Reviewed in the United States on July 29, 2024
Good and durable switches for my offroad vehicle
Jan D
Reviewed in Belgium on February 16, 2024
Zoals het hoort
Stjepan Mijatovic
Reviewed in Germany on November 24, 2024
weiter so
Stan
Reviewed in the United States on October 3, 2024
Switches look to be great. Came with everything needed for installation. Only complaint is the small wire connection area.
Roussel Marcel
Reviewed in France on October 29, 2024
Installé OK
F1RXM
Reviewed in France on October 23, 2024
utilisé sur secteur 230v ,fonctionne correctement depuis quelques mois
Babbage
Reviewed in the United Kingdom on October 19, 2024
Perfect for what I wanted - an ignition switch for a ride-on mower (to go with a separate starter button).Good action, each switch versatile as two independent on-off or cross-over switches. Perfect. And the best value I found.
Recommended Products
$17.00
$ 6 .99 $6.99