Your cart is empty.
Your cart is empty.
- On - Off - On position control and 12 terminals design.
- Suitable for the thickness between 1mm to 4mm of the mounting board.
- Suitable for a wide range of applications, it can be applied as a circuit control switch, master control switch, testing equipment control switch, or change-over switch for electric welding machinery and other equipment.
Forsenik
Reviewed in Canada on August 20, 2024
Its well made with good materials. However, It had no contact map included and when I checked it, it was:position 1: 1-2, 3-4, 5-6 and position 2: 7-8, 9-10, 11-12 not as the map on the product info.
Mattias
Reviewed in Canada on June 13, 2024
I used two of these in a panel I built and I only use them for dry contacts so I can't speak to their current capacity but they work great for some cheap dry contact switches.
William Cook
Reviewed in the United States on March 14, 2024
Reversing switch
William Diaz
Reviewed in the United States on February 26, 2024
Used to reverse rotation on an AC motor. Works great. Plenty of tabs and I used all of them. Motor had 4 wires. 1 neutral , 4 line, and 2 and 3 switch N and L depending on rotation.So took a bit of planning to feed line to 4 and 2 in position 1, 4 and 3 on position 2. And the same with neutral. 1 and 3 on position 1 and 1 and 2 on position 2. Switch in the middle keeps all disconnected
Bluff
Reviewed in the United States on February 17, 2024
Instruction diagram is a bit vague. I double checked with ohm meter. It works well
Leo
Reviewed in the United States on August 17, 2020
Great quality at a price that can’t be beat!It can be tricky to understand the wiring diagram depending on the configuration needed, like in a three phase forward and reverse.
R Sing
Reviewed in the United States on November 29, 2020
These type of switches are very useful for switching circuits from one power source to another. They have a good rating of usually 15 to 20 amps and 600 volts. I use them to switch some of my home circuits from grid to solar and vice versa. The usual shunts out there are very expensive. With a little wiring know how and this switch you can do the same thing for a lot less. I build boxes for them which need to be larger that a traditional electrical box since they are a bit bulky. However, they are very good switches. One drawback is there are no instructions or they are in some other language. Thus, to determine where to place the wires and what connects to what, I use a multimeter and look at the resistance. If there is resistance then the circuit is not connected. If resistance reads 0, then the circuit is connected.
Customer
Reviewed in the United States on September 16, 2019
Baomain 660V 20A On-Off-On 3 Positions 12 Terminals Changeover Control Rotary Cam SwitchJust installed this item as a transfer switch for my 230-volt AC well pump. I wanted backup power for our planned utility (PGE) outages. I use a 2200-watt gas generator and a transformer to get 230 power. Switch looks okay, although I would recommend switching under no load or reduced load. Trim wire insulation to 5/16” [7mm].The enclosure (see below) needs some work. Add four 3/16” holes for switch. No need to counter sink these. Remove boss. 7/8” step drill works well. Generator will work outside my pump house. Feed through spec below.See pictures for schematic drawings.Baomain Master Switch Exterior Box LW28-63/4 Work for Universal Rotary Changeover Cam Switch SZW26-63 660V 63A 3 Position 3 PhaseLeviton 5278-CWP Straight Blade Flanged Male Power Inlet Receptacle, 15 A, 125 V, Nylon Face, Body And Strap
James Bullard
Reviewed in the United States on December 28, 2019
Used for hot tub pump. Working great.
Leo
Reviewed in the United States on August 20, 2018
Used this to install a reverse option for my little girl's 12v ride-on toy car. They worked awesome. Good quality.
Recommended Products
