Your cart is empty.
Your cart is empty.Product Description
Upgraded furnace flame sensor 62-23543-01 for Rheem &Ruud62-23543-01 Flame Sensor Rod，2Pack
COMPATIBLE
- Replace Part :62-23543-01,62-23543-02, 62-23543-03, 62-23543-04
- FITS Model :NORGDG, SGDG, RGDJ, RGFD, RGLG, RGLH, RGLJ, RGLK, RGLL, RGLN, RGLQ, RGLR, RGPH, RGPJ, RGPK, RGPL, RGPN, RGPP, RGPQ, RGPR, RGRA, RGRB, RGRJ, RGRK, RGRL, RGRM, RGSA, RGTA, RGTJ, RGVG, RGVH, RGVJ, 80LJ, 80LS, 80PJ, 80PS, 90RJ, 90RS, 90RT, 90TJ, 90TS, RGFE, RGFG, RGLE, RGLS, RGLT, RGPE, RGPS, RGPT, RGRS, RGRT, RGTS, SGPG, SGPN
PART INFORMATION
flame sensor flame sensor (part number 62-23543-01) is for Rheem &Ruud furnaces.(2PACK)
SPECIFICATION
- ►Length (Mounting Flange to Sensor Tip): 2-1/2"
- ►Length-Sensor Offset: 1-9/161
- ►Angle - Sensor Offset (degrees): 90. ►Termination: 1/4" Male Quick Connect
- DURABILITY
- Made of high-quality and wear-resists metal and ceramics, and it had been well-tested by the manufacturer, can last for long.
INSTALLATION STEPS
STEP 1&STEP 2
►Shut off the power to your furnace (or any other appliance), prior to making any repairs. There will usually be a light switch (toggle switch)on or near your furnace. If this switch is not present, furnaces have a dedicated breaker; locate your furnace breaker and shut your unit down.
► Remove the Sensor. Find the broken sensor. The sensor is easily accessible and typically mounted by one 1/4” hex head screw. Upon removing this screw, the sensor will slide out so that you can easily clean it. Carefully remove the sensor;
STEP 3
Remove one sensor and replace it with our new sensor.
STEP 4
Simply reconnect the wire if you’ve taken it off, remount the sensor to the burner assembly using the 1/4” screw, replace the door(s) on the unit, and turn the power back on.
STEP 5
Check Your Results. If the unit takes a few extra seconds to start up or the fan immediately kicks on and runs for a bit, this is normal. Shutting down the power to the unitcan cause it to reset and run through a short series of checks before trying
charles
Reviewed in the United States on February 6, 2025
It was something that I needed and the price was right and they worked great
Joe Consumer
Reviewed in Canada on February 5, 2025
Not compatible for RGRM furnace as said. The unit received does not match the picture shown in the sales ad.The received part is too short and has the wrong orientation. The flange MIGHT be able to be moved to fix the orientation and add some length but it is pretty tight on the ceramic.
A. Hilsenteger
Reviewed in Canada on February 23, 2025
Did not fit my Rheem furnace. Not even close to 62-23543-01, the part I was trying to replace. Wrong length, wrong fit.
Debi
Reviewed in the United States on February 22, 2025
In the middle of freezing temps in Ohio our furnace started acting up. I ordered this part on amazon and my husband was able to easily install it, furnace is back to working like brand new…and this part was delivered to us the very next day after I ordered it.
Scott L
Reviewed in the United States on February 17, 2025
Perfect fit. Work well.
Ryan Z
Reviewed in the United States on February 13, 2025
Check your model numbers first!This was a perfect fit for my unit, quality is great and came with 2 in the pack.I installed and it has been working for 5 days with zero issue.
Chris R Smith
Reviewed in the United States on January 20, 2025
I was without heat for a couple days and was very excited to get this product in and hopefully get my heat back up and going. It was delivered quickly, I had it installed in about 10 minutes and my heat was back up and going. Excellent product and service.
Customer
Reviewed in Canada on January 16, 2025
This item is approximately half an inch shorter than the proper part.
Jimbo
Reviewed in the United States on May 14, 2024
Very quick & easy fix for my gas furnace which seemed to be going out occasionally over the span of about 1 week. Did some research & it sounded like I may need to replace this - I pulled my old one out (easy to do, look on YouTube) & it was indeed kind of dirty/worn so I cleaned it up a little w/ emery paper & I was right back in business. I ordered a 3 pack of these replacements for cheap, I used one to replace the old one I had cleaned up for temporary use, and taped the other 2 to the side of my furnace so they’re right there when I’d ever need to replace one again.
Greg f.
Reviewed in Canada on March 16, 2024
nothing to dislike just like OEM works great and got 3 of them
Jp
Reviewed in the United States on February 4, 2024
I bought this part as a spare part so I don't have a comment flame sensor is a fail point for most furnace
Sandy
Reviewed in the United States on December 4, 2024
My flame sensor was going out so my furnace was cycle on and off.The electrical connection fits perfectly and it works perfectly on the first try..
Recommended Products