Your cart is empty.
Your cart is empty.Product Description
2" and 3" angle orbital air sander detailed
Kindly reminder:
Before you use the air sander, please add 2-3 drops of oil from air quick connector and please allow the tool to run for a few seconds after filling to make sure it works well. (oiler not included in our box)
This tool is intended to be operated as a handheld tool and is air-powered. It requires an air compressor that will provide a clean lubricated air, where the air hose is connected to the tool when the tool is running.
Different angle views for 2" and 3" angle orbital air sander
Safe pressure plate type start-stop switch for safer users and higher reliability
Stepless speed control knob switch, according to different purposes, choose the different speed to meet different needs
The 2-inches or 3 inches hook and loop sanding pad easy replaced, that is lightweight and suitable for small areas of grinding and polishing
Before use, add 2-3cc #60 pneumatic oil to the air inlet to make the fan blade better lubricated. the cylinder cooling then maintains the torque and delays the life of the machine
How to replace hook and loop sanding pad for angle orbital air sander
Replace sanding pad step one
Find the small hole on the top of the angle orbital sander. If you don't find the hole near the outside, use the PIN to hold the rotating block inside. Rotate it a little to find it, then insert it into the hole with the PIN.
Replace sanding pad step two
Hold the PIN, do not let the PIN slide, rotate the sanding pad in the direction of the arrow until the disk is removed from the angle track mill
Internal eccentric view for angle orbital air sander
You can find how is the structure for Internal eccentric view of angle track sander
Replace sanding pad step three
Continue to withstand the PIN, do not let the PIN slide, according to the direction of the arrow in the picture, installing the new sanding pad to angle orbital sander
Instruction manual for angle orbital air sander
- Please check off all tightening parts of the tools to be in good condition before operation.
- Working pressure to be 6.3 kg/cm3 (90PSI) at operation.
- Please refer to Figure 1 for the tool installation. To install a filter and a lubricator/oiler at an air outlet
- The best hand stress on the tool is from 5Kg to 7Kg when operation.
- Release the air supply when replacing the sandpaper or the backing pad.
- Wear protection glasses, eye protector, dust mask and gloves at operation.
- Have a short break in every 30minutes to avoid any possible injury due to tiredness.
- Do not have free rotating at high speed to avoid possible injury to the human body and possible tool damage.
- Do not touch the rotating part of the tool with your hand or your body at operation.
- Start your sanding job after you fit the sanding pad flat on the surface you are working on. Please refer to Figure 2.
Routine maintenance for angle orbital air sander
- Stop your Job when finding any irregular sound or vibration at operation and then check and repair the tool.
- Because you are using clean compressed air at operation. Use an air filter at the air installation to clean the dust out of the compressed air.
- Drop some Oil to the inlet of the tool and then run the tool slowly for a minute and finally start your work...Auto Lubricator/oiler is recommended.
- Any dirt dust inside the motor may result in slow rotation even block running, at this time, try to drop some oil from the inlet, see whether solve the problem or return to the seller for maintenance.
- Do release the water out of the air compressor and air hose after an operation.
- Maintain tools with care. Keep tools clean for better and safe performance, follow instructions for lubricating. Inspect tools cords and air hoses periodically, if damaged, have them repaired by an authorized technician.
Melinda D
Reviewed in the United States on May 26, 2024
The collar broke 1st day I used it. I guess it's hit or miss on these. I would pay more to get a better product but it looks like they are all the same.
Stéphane Ouellet
Reviewed in Canada on January 27, 2024
Très bon produit
Johng
Reviewed in the United States on November 29, 2023
A good value for money, but it really needs an air valve to be fully functional. These values are readily available from Amazon and I suggest ordering the at the same time (and the valve does not need to close completely - this is an addition to the tool's control).Caveats:- the paddle control is way to sensitive to be useful, at least for me- the air valve I purchased has the valve right at the base, of the tool where it was too easy to bump with the bottom of my hand, thus the 3-star 'ease of use rating'. It's very easy to use the tool full-on, but I found virtually impossible to control the speed with the on-tool control.- the discs (2") are very small, with a correspondingly small surface area. So I used up the disc extremely quickly. This isn't a criticism of the tool, it's just a note that if you're doing more than a small job you'll want to purchase lots of extra discs, and preferably good quality ones.- This does use a moderate volume of high-pressure air; I can't see this working well with e.g. a pancake compressor.I also read the reviews about overheating the discs and wrecking them. They heat quickly so take it easy and check them. I found the sanding discs tended to shift a bit in use, exposing the edge of the backing pad. I suspect this is routine.Overall, I used this to refinish car wheels and it worked great. The wheels were old and corroded and this save LOTS of work and sore fingers. Oil regularly while using and I'm expecting it'll last a long time with my very limited DIY use. It doesn't appear to be professional quality, but a good value. I think the disk backing is also a non-standard size so this might require some effort to replace when they wear out.
Serge Alain Pelletier
Reviewed in Canada on September 7, 2022
J’ai sablé les phares de trois voitures. Excellent résultat.
Duane
Reviewed in the United States on August 17, 2022
I purchased this to rehab my sun damaged headlights on my Mercedes. It worked great! See the before and after pix. It's super easy to use, easy to handle and I can't imagine a better value for the price. There are no directions so I had to Google how to tighten the sanding head to the gun, but after that...all good.
Think7
Reviewed in the United States on October 23, 2022
Tried it for 30-60 minutes with various grits and it is fair. Pad/foam quality is iffy and that directly affects how the paper performs. The advertised "speed control regulator" is the same slotted head air flow control that you see on many air tools. It throttles the RPMS slightly but in no way, shape or form has the same type of control that an inline add-on regulator has. This one effectively gives you 2 speeds and the slower one is hardly noticeable. You get what you pay for and this may be suitable for occasional use. Definitely not pro quality and it is going back to Amazon.
G.W. Retired Racer
Reviewed in the United States on May 27, 2021
Works great and very reasonable price. Even if I only get a years worth of use out of it, I'll still be happy. I'll just throw it in the trash and buy another one. So far... it's a great bargain.
gaetan
Reviewed in Canada on December 14, 2021
sablage métal semble de qualité acceptable pour le prix mais quel sera la duré de l,outil
Michael Marshall
Reviewed in the United States on August 2, 2020
I polish aluminum on semi trucks and needed something smaller for the harder to reach areas and recently bought an electric polisher that was the same size but it just wasn’t powerful enough. This one has more power than I need. It does the job effortlessly and without bogging down. Easy to operate and with no more vibration than to be expected. It is a great tool for the money.
Elvis
Reviewed in the United States on March 10, 2020
Ma agradó el poder pulir áreas pequeñas con mucha comodidad. No es costo efectivo porque el compresor de aire continuamente se activa . Para detailing conviene más uno eléctrico
Chopstix Kid
Reviewed in the United States on April 8, 2020
Super value. I use this several times a week and it has held up well. The speed control can be a little flaky at times but compared to units that cost 3-4 time more, I am very happy with it.
Recommended Products